This patch updates OpenSBI version to 1.4 as part of
release preparation.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
OpenSBI uses time CSR if Zicntr extension present which causes
it to crash on an older QEMU because QEMU generates Zicntr in
the ISA string for unleashed machine which only has CYCLE and
INSTRET counters.
Fixes: 776770d2ad ("lib: sbi: Using one array to define the
name of extensions")
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
The parser will fail if the timer is clint timer and has regname
property. As the regname is only meaningful for aclint, it is more
robust to only check regname for aclint timer.
Fixes: 6112d58 ("lib: utils/fdt: Allow to use reg-names when parsing ACLINT")
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
There is a problem with judging whether the current hart belongs to
hmask. If cur_hartid minus hbase is greater than BITS_PER_LONG, the
previous hmask will also have a bit cleared incorrectly, which will
cause some harts to lose ipi.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
On platforms with Smepmp, the previous booting stage must enter
OpenSBI with mseccfg.MML == 0. This allows OpenSBI to configure
it's own M-mode only regions without depending on the previous
booting stage.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
The SBI_ETRAP error code was introduced only for doing trap
redirection in generic sbi_ecall_handler(). Now the trap
redirection is moved into sbi_ecall_legacy.c and SBI_ETRAP
error code is only used in this source file so let us remove
it.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Some of the upcoming SBI extensions (such as SSE) will directly
update register state so improve the prototype of ecall handler
to accommodate this. Further, this flexibility allows us to
push the trap redirection from sbi_ecall_handler() to the
sbi_ecall_legacy_handler().
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
On platforms with Smepmp, the MMIO regions accessed by M-mode need
to be explicitly marked with M-mode only read/write or shared (both
(M-mode and S-mode) read/write permission.
If the above is not done then runtime PLIC access from M-mode on
platforms with Smepmp will result in access fault when further
results in CPU hotplug not working.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Let's use SBI_TLB_INFO_SIZE instead of hard-coded 0x40 in
fw_platform_calculate_heap_size() to fine tune the heap size
required for per-hart TLB fifos.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Let us reduce the size of struct sbi_tlb_info by doing the
following:
1) Change the data type of asid and vmid fields to uint16_t
2) Replace local_fn() function pointer with an enum
Based on the above, the size of struct sbi_tlb_info is reduced
by 16 bytes on RV64 and 4 bytes on RV32.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Enable access to some extensions through menvcfg and show them in "Boot
HART ISA Extensions" if they are present in the device tree.
Signed-off-by: Yong-Xuan Wang <yongxuan.wang@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Define an array sbi_hart_ext to map extension ID and name , and use it
for ISA parsing and printing out the supported extensions.
Signed-off-by: Yong-Xuan Wang <yongxuan.wang@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
We can enhance the code by creating 2 unified interface with macro for
privilege mode and extensions detection, which relies on supported
privilege modes and CSRs.
Signed-off-by: Yong-Xuan Wang <yongxuan.wang@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The original code has multiple conversions between hartid and
hartindex. Can call sbi_hartmask_set_hartindex directly to
avoid conversion.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
sbi_ipi_event_create() disallows registering an IPI event with a NULL
.process callback, so the function pointer will never be NULL here.
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Xiang W <wxjstz@126.com>
An IPI sent to the local hart can be processed directly instead of
triggering the IPI device. This is more efficient, and it avoids a
deadlock when the .sync callback is defined. Since interrupts are
disabled while handling an ecall, the IPI would not get delivered
until the next mret, but sbi_ipi_sync() is called before then.
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Xiang W <wxjstz@126.com>
Currently, failures in sbi_ipi_send() are silently ignored, which makes
them difficult to debug. Instead, abort sending the IPI and pass back
the error, but still synchronize any IPIs already sent.
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
The tlb_update() callback is called for each destination hart.
Move the size check earlier, so it is executed only once.
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Currently, the fdt_parse_aclint_node() follows a fixed order to parse
ACLINT timer. This may cause the undesirable result when the ACLINT
device does not support mtime without adding an empty entry for it in
the DT.
To be robust, make fdt_parse_aclint_node() support "reg-names" property,
so it can parse the DT in an order independent way. For compatibility,
fdt_parse_aclint_node() only use "reg-names" when parsing ACLINT timer,
and will fallback to the old way if "reg-names" property is not found.
Link: https://lore.kernel.org/all/20231114-skedaddle-precinct-66c8897227bb@squawk/
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Reviewed-by: Anup patel <anup@brainfault.org>
When warmboot via HSM, coolboot has been completed and
wait_for_coldboot can be skipped to speed up.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Previous patch introduced a change that using hart count as the default
number of tlb entries in the fifo. This makes the default tlb fifo size
grow in square with the number of harts. So the default heap size is
not enough to allocate tlb fifo when the hart count is big.
Fixes: 52fd64b ("platform: Uses hart count as the default size of tlb info")
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Current interruptible hart mask doesn't include the hart which HSM state
is SBI_HSM_STATE_RESUME_PENDING. So when there is a request to send an
IPI to the hart which is in the resume process, this hart would miss the
IPI forever. Put the SBI_HSM_STATE_RESUME_PENDING hart in the
interruptible hart mask to fix the issue.
Signed-off-by: Nick Hu <nick.hu@sifive.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The counter info should only return valid hardware counters for the ones
set in the counter mask. Otherwise, it will report incorrect number of
hardware counters to the supervisor if the platform has discontiguous
counters.
Fixes: c744ed77b1 ("lib: sbi_pmu: Enable noncontigous hpm event and counters")
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
OpenSBI doesn't support SBI PMU snapshot yet as there is not much benefit
unless the multiple counters overflow at the same time.
Just add the definition and return not supported error at this moment. The
default returned error is also not supported. Thus, no functional change
intended.
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Multiple harts may try to send IPI to a particular target hart A
in which case the send_ipi() should be called only when the old
value of the hart A ipi_type is zero.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Simplify atomic-related bit operations through __atomic intrinsics.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The original code returns the value of the word before modification.
When modifying the upper 32 bits under RV64, the value returned via
int return will have no meaning. Corrected to return the value of the
bit. And modify the function description.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
lr/sc is part of the A extension. If the A extension is not supported,
lr/sc cannot be used. So remove xchg/cmpxchg.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Add PMU node example for event index to counter index mapping
and selector value translation of Andes' CPUs.
Currently, there are 4 HPM counters that can be used to monitor
all of the events for each hart.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Locus Wei-Han Chen <locus84@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
The valid entry count is tracking by hw_event_count so there
is no need to check the whole table.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
To allow platform override pmu_init() filling the translation table
fdt_pmu_evt_select[] when PMU node doesn't provide such information,
we need to share the table and its entry counter with other .c file.
We also define the structures of PMU property in fdt_helper.h, so we
can initialize the mappings in arrays.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
We will need is_andes(45) in the following patch,
so factor out the code that parses marchid to make
it reusable for checking any Andes CPU variants.
Also improves the comment in ae350_hart_start().
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Add a Kconfig option to control PMU fixup, so the next
stage software can dump the PMU node including event
mapping information for debugging purposes.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Before the ratification of Sscofpmf, the Andes PMU extension
was designed to support the sampling and filtering with hardware
performance counters (zihpm), it works with the current SBI PMU
extension and Linux SBI PMU driver.
We implement 1) the PMU device callbacks that update the
corresponding bits on custom CSRs, 2) extentions_init() to detect
the hardware support of Andes PMU and initialize the per-hart
PMU related CSR, and 3) pmu_init() to register PMU device and
populate event mappings.
Also define a andes_pmu_setup() function which is in preparation
for adding default PMU mappings in andes_hpm.h
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Add support for custom PMU extensions to set inhibit bits
on custom CSRs by introducing the PMU device callback
hw_counter_filter_mode(). This allows the perf tool to
restrict event counting under a specified privileged
mode by appending a modifier, e.g. perf record -e event:k
to count events only happening in kernel mode.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
This patch makes the following changes:
- As sbi_platform_pmu_init() returns a negative error code on
failure, let sbi_pmu_init() print out the error code with
sbi_dprintf().
- In order to distinguish the SBI_EFAIL error returned by
sbi_pmu_add_*_counter_map(), return SBI_ENOENT to indicate
that fdt_pmu_setup() failed to locate "riscv,pmu" node, and
generic_pmu_init() ignores such case.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
The old scheme doesn't allow sending hart0 self-IPI as the
corresponding bit on pending register is hardwired to 0, this
could lead to unhandle IPIs on SMP systems, esp. on single-core.
Furthermore, the limitation of old scheme is 8-core, instead of
reserving source hart information, we assign bit (x + 1) as the
enable and pending bit of hartx, this also expands the bootable
hart number.
The following diagram shows the enable bits of the new scheme
on 32-core Andes platform.
Pending regs: 0x1000 x---0---0---0---0------0---0
Pending hart ID: 0 1 2 3 ... 30 31
Interrupt ID: 0 1 2 3 4 ... 31 32
| | | | | | |
Enable regs: 0x2000 x---1---0---0---0-...--0---0---> hart0
| | | | | | |
0x2080 x---0---1---0---0-...--0---0---> hart1
| | | | | | |
0x2100 x---0---0---1---0-...--0---0---> hart2
| | | | | | |
0x2180 x---0---0---0---1-...--0---0---> hart3
. . . . . . .
. . . . . . .
. . . . . . .
0x2f00 x---0---0---0---0-...--1---0---> hart30
| | | | | | |
0x2f80 x---0---0---0---0-...--0---1---> hart31
<-------- word 0 -------><--- word 1 --->
To send IPI to hart0, for example, another hart (including hart0
itself) will set bit 1 of first word on the pending register.
We also fix indentation in andes_plicsw.h along with this patch.
Fixes: ce7c490719 ("lib: utils/ipi: Add Andes fdt ipi driver support")
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Randolph <randolph@andestech.com>
Reported-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lists.infradead.org/pipermail/opensbi/2023-October/005665.html
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Currently, there are no barriers before or after the ipi_clear()
device callback which forces ipi_clear() device callback to always
use non-relaxed MMIO writes.
Instead of above, we use wmb() in after the ipi_clear() device
callback which pairs with the wmb() done before the ipi_send()
device callback. This also allows device ipi_clear() callback
to use relaxed MMIO writes.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reported-by: Bo Gan <ganboing@gmail.com>
Currently, we have a smp_wmb() between atomic_raw_set_bit() and
ipi_send() device callback whereas the MMIO writes done by the
device ipi_send() callback will also include a barrier.
We can avoid unnecessary/redundant barriers described above by
allowing relaxed MMIO writes in device ipi_send() callback. To
achieve this, we simply use wmb() instead of smp_wmb() before
calling device ipi_send().
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reported-by: Bo Gan <ganboing@gmail.com>
Each APLIC CLRIE register allows disabling 32 interrupt sources at
a time by writing -1 so no need to write CLRIE register separately
for each interrupt source.
Fixes: 99792653de ("lib: utils/irqchip: Add APLIC initialization library")
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
total_ctrs is bounded by
SBI_PMU_FW_CTR_MAX + SBI_PMU_HW_CTR_MAX) == 48
which exceeds BITS_PER_LONG on 32 bit systems.
Iterating over the bits of &cmask results in a buffer overflow when looking
for a bit >= BITS_PER_LONG.
Adjust the iterators in sbi_pmu_ctr_start() and sbi_pmu_ctr_stop()
accordingly.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The sbi_hart_map_saddr() must create PMP mapping of size greater
than or equal to PMP granularity otherwise PMP mapping does not
work when size parameter less than sbi_hart_pmp_granularity(scratch).
Fixes: 6e44ef686a ("lib: sbi: Add functions to map/unmap shared memory")
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Samuel Holland <samuel.holland@sifive.com>
For some debuggers that do not implement SYSWRITEC and SYSREADC
operations, we have to use SYSWRITE and SYSREAD.
Instead of implementing semihosting_putc() using SYSWRITE, let us
simply remove semihosting_putc() because console_putc/console_puts
are now interchangeable.
Signed-off-by: Chen Pei <cp0613@linux.alibaba.com>
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
console_puts/console_putc should replace each other, but the previous
sbi_putc can only use console_putc. This patch addresses this problem.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
In the future there may be a lot of ISA extensions, a 'long' may not
be able to accommodate, changed to an array for the future.
Addresses-Coverity-ID: 1568357 Out-of-bounds access
Fixes: 6259b2ec2d ("lib: utils/fdt: Fix fdt_parse_isa_extensions()
implementation")
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
If ISA extension Zkr is available, set
mseccfg.sseed=1
mseccfg.useed=0
This enables access to the seed CSR in S-mode but not in U-mode.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
- Add Zkr as extension in sbi_hart_extensions enum
- Return "zkr" string for Zkr extension from sbi_hart_extension_id2string
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Define macros to access the sseed and the useed bit in the machine
security configuration register (mseccfg).
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
As the domain will reject a new memory region which has a sub-regions
already in the domain, even the new region is bigger and has the same
flags. This problem can be solved by relaxing region restriction and
rechecking when adding and sanitizing domains.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Swapping domain region is a common operation when sorting domain region,
so separate it as a function to make code clean.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The quirks checking will cause ACLINT step into a CLINT code path, this
is not expected when ACLINT needs custom quirks.
Add a new quirk to identify custom ACLINT, and apply the general quirks
after applying CLINT specific quirks.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
In the past, we used fdt_reset_thead to help customers with prototype
verification. However, with the emergence of the Big-little SoC system,
it can no longer meet the demand. Therefore, we use zero_stage_boot
instead of fdt_reset_thead. It cleans up the opensbi code and ends the
disputation of reset_sample's dts.
This patch removes the fdt_reset_thead component and updates the related
doc.
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Signed-off-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
It's wrong to put the fence after setting the boot status flag because
all relocation operations must be finished before setting the status
flag. So, this fence must be put before the setting status flag, and
there is no use in putting a fence between _start_warm and setting
status flag.
Also, nop can't delay other harts too much, so use div instead, just
like Linux cpu_relax. Current opensbi force enables “M” Standard
Extension, and mul instructions have been used in the fw_base.S.
After the above two fixes, the boot hart index param of the
fw_dynamic_info could be guaranteed properly for all platforms.
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Signed-off-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
For some debuggers that do not implement SYSWRITEC and SYSREADC
operations, we can use SYSWRITE and SYSREAD instead like the
implementation of semihosting_getc().
Signed-off-by: Chen Pei <cp0613@linux.alibaba.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
For platform with high number of harts, it is better to auto detect a
suitable number of entries in tlb fifo. Since allocating tlb entry for
all online harts can reduce the wait time significantly, using the
number of the online harts can make most platforms happy. This auto
detection can avoid most duplicate code for setting tlb fifo size.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Acked-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Flushing the tlb entries can solve the thead tlb problem, but flushing
it by address will miss something and lead to a exception in some rare
cases, and this is more common for sg2042.
To solve this problem, flush the tlb entries by asid in the custom trap
handler to ensure it is refreshed.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
Per the SBI specification, the effects of these functions are limited to
a specific ASID and/or VMID. This applies even when flushing the entire
address space.
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Since all the SoC with thead c9xx cores need this initialization at now,
initialize the c9xx pmu in the thead generic platform by default.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Separate the implement of T-HEAD c9xx errata to allow any platform
with bug related to c9xx cores can use it.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Separate the implement of T-HEAD c9xx pmu to allow any platform with
c9xx cores can use it.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The CSR encoding for t-head c9xx cores is shared across all the
platforms with these cores. So move header thead_c9xx.h to the
thead subdir.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Acked-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
Since commit 112daa2e64 ("lib: sbi: Maximize the use of HART index in
sbi_domain") the platform parameter is unused.
Fixes: 112daa2e64 ("lib: sbi: Maximize the use of HART index in sbi_domain")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Now that SBI v2.0 specification is frozen, we change spec version
implemented by OpenSBI to v2.0.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Unlike C.LWSP/C.LDSP, these encodings can be used with the zero
register, so checking that the rs2 field is non-zero is unnecessary.
Additionally, the previous check was incorrect since it was checking
the immediate field of the instruction instead of the rs2 field.
Signed-off-by: Amanieu d'Antras <amanieu@gmail.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
RISC-V privileged specification v1.12 introduced the mconfigptr CSR
which will hold the physical address of a configuration data
structure.
Signed-off-by: Yangjie Zhang <jay1273062855@outlook.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
"Zicsr" isa extension has been separated from "I" extension.
This patch add the isa requirement of "Zicsr" extension in
platform requirements documentation.
Signed-off-by: Yangjie Zhang <jay1273062855@outlook.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
In starfive_gpio_direction_output() readl() is called twice to read the
gpio direction register. The result of the first read is discarded.
Remove the redundant read.
Fixes: 908be1b85c ("gpio/starfive: add gpio driver and support gpio reset")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
sbi_pmu_ctr_cfg_match() receives data from a lower privilege level mode.
We must catch maliciously wrong values.
We already check against total_ctrs. But we do not check that total_ctrs is
less than SBI_PMU_HW_CTR_MAX + SBI_PMU_FW_CTR_MAX.
Check that the number of hardware counters is in the valid range.
Addresses-Coverity-ID: 1566114 Out-of-bounds write
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
The define is hard to read. The continue statement does not do what was
intended.
* Remove do {} while (false);
* Change the name to set_multi_letter_ext
- Other local macros are lower case too.
- Refer to the fact that this is only used for multi-letter extensions.
Addresses-Coverity-ID: 1568359 Unexpected control flow
Fixes: d72f5f1747 ("lib: utils: Add detection of Smepmp from ISA string in FDT")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
hart_exts == NULL can only occur if offset and node address lead to an
overflow resulting in exactly NULL. As we don't catch other values of
overflow it does not make sense to treat this one as special.
Addresses-Coverity-ID: 1568355 Logically dead code
Addresses-Coverity-ID: 1568358 Logically dead code
Fixes: 6259b2ec2d ("lib: utils/fdt: Fix fdt_parse_isa_extensions() implementation")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
'1' is a 32 bit integer. When shifting it by more than 31 bits it becomes
zero and we get an incorrect return value.
Addresses-Coverity-ID: 1568356 Bad bit shift operation
Fixes: 296e70d69d ("lib: sbi: Extend sbi_hartmask to support both hartid and hartindex")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The added memory region should start from the base address.
Otherwise, the range will be shifted by reg_offset and not
able to merge consecutive NAPOT regions in the root domain,
resulting in wasted PMP entries.
Fixes: e8bc1621 ("lib: utils/serial: Add shared regions for
serial drivers")
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The base of .text is defined by `FW_TEXT_START`, not `FW_TEXT_BASE`.
Signed-off-by: Hoa Nguyen <hn@hnpl.org>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Since everything is statically linked, we don't need to expose symbols
for dynamic linking.
For a default build this saves about 2 KiB of useless read only data in
.dynsym, .dynstr, .hash, .gnu.hash sections.
Signed-off-by: Vivian Wang <dramforever@live.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Since everything is statically linked, we won't actually have
R_RISCV_{32,64} relocations. No need to handle these.
Fixes: 0f20e8adcf ("firmware: Support position independent execution")
Signed-off-by: Vivian Wang <dramforever@live.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The .rela.dyn section should be exactly the size of the relocations,
without padding. On RV64, .rela* sections are already aligned and
there's no need for padding. On RV32, this adds padding up to 4 bytes,
which, if present, confuses the relocation loop into processing an extra
entry past the end of .rela*, and it crashes with an invalid memory
access.
Fixes: 0f20e8adcf ("firmware: Support position independent execution")
Signed-off-by: Vivian Wang <dramforever@live.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The TLB entries remain functional all the time once added in T-HEAD th1520
and Sophgo sg2042 (even if the MMU is then disabled afterwards). If there
are some stale TLB entries that contains the address of SBI, it will cause
unexpected memory access and issue a illegal instruction error. To avoid
this, a TLB flush is needed to drop these TLB entries before any memory
access in the trap handler.
To handle this workaroud, add a custom trap handler with executing TLB flush
first in the T-HEAD platform to fix affected socs.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The syscon region used by OpenSBI should be marked as a shared
read-write region between M-mode and SU-mode.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
The serial driver regions used by OpenSBI should be marked as a shared
read-write regions between M-mode and SU-mode as those are accessed
by earlycon and the corresponding tty serial drivers running in 'S' mode.
When the smepmp extension is enabled, PMP entries for these shared regions
will get programmed.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Based on sections 4.c and 4.d in Ch.2 of the Smepmp spec the PMP entries
must be programmed as below:
1. Program M-only entries
2. Enable mseccfg.MML
3. Program shared-region entries
4. Program SU-only entries
Co-developed-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
The Smepmp read-only shared region must have pmpcfg.L, pmpcfg.R,
pmpcfg.W, and pmpcfg.X bits set so sbi_hart_get_smepmp_flags()
must return pmp_flags accordingly.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
The mseccfg.MML bit is a sticky bit which remains unchanged once set
so no need to clear it in sbi_hart_smepmp_configure().
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Let us factor-out Smepmp configuaration as separate function so
that code is more readable.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
The macros to test permissions must perform an exact match of all the
bits in the input with the desired permission bits. Otherwise, the check
returns false positives in those cases where only some of the desired
permissions are set in the input.
Fixes: 6c202c5 ("include: sbi: Add Smepmp specific access flags for PMP
entries")
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The sbi_hartmask_for_each_hart() macro is slow and has only one user
so let us completely remove the sbi_hartmask_for_each_hart() macro.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Let us maximize the use of HART index in sbi_domain because hartindex
based hartmask access and sbi_scratch lookup is faster.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
The sbi_scratch_last_hartid() macro is not of much use on platforms
with really sparse hartids so let us replace use of this macro with
other approaches.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Let us prefer hartindex over hartid in IPI framework which in-turn
forces IPI users to also prefer hartindex.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
The sbi_hartid_to_scratch() involves translating hartid to hartindex
which is expensive so let's use sbi_hartindex_to_scratch() instead.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Currently, the sbi_hartmask is indexed by hartid which puts a
limit on hartid to be less than SBI_HARTMASK_MAX_BITS.
We extend the sbi_hartmask implementation to use hartindex and
support updating sbi_hartmask using hartid. This removes the
limit on hartid and existing code works largely unmodified.
Signed-off-by: Xiang W <wxjstz@126.com>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
The hartid to hartindex mapping is now tracked in sbi_scratch so we
don't need sbi_platform_hart_index() and sbi_platform_hart_invalid()
functions hence let us remove them.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
We introduce HART index and related helper functions in sbi_scratch
where HART index is contiguous and each HART index maps to a physical
HART id such that 0 <= HART index and HART index < SBI_HARTMASK_MAX_BITS.
The HART index to HART id mapping follows the index2id mapping provided
by the platform. If the platform does not provide index2id mapping then
identity mapping is assumed.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
We found the mstatus.FS status is not set correctly after the SET_F64_REG()
and SET_F32_REG(). We should set mstatus.FS dirty after we emulate the FPU
instructions.
Co-developed-by: Roy Lin <roy.lin@sifive.com>
Signed-off-by: Roy Lin <roy.lin@sifive.com>
Signed-off-by: Greentime Hu <greentime.hu@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
If the system is defined from tlb_fifo_num_entries, the scratch may be
too small to hold the fifo, so it is alloc through the heap.
Signed-off-by: Xiang W <wxjstz@126.com>
Signed-off-by: Xing Xiaoguang <xiaoguang.xing@sophgo.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
For some platforms with a particularly high number of harts, if the
tlb fifo is too small, it case harts to wait. Platforms should be
allowed to specify the size of the tlb fifo.
Signed-off-by: Xiang W <wxjstz@126.com>
Signed-off-by: Xing Xiaoguang <xiaoguang.xing@sophgo.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
After the hardware hpm counter is stopped, it should not raise any new
interrupt as it is already stopped. So add the hw_counter_disable_irq
callback to allow the custom pmu device to control this behavior.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
Tested-by: Samuel Holland <samuel@sholland.org>
T-HEAD c9xx pmu needs to clear OV bits of MCOUNTEROF in any condition
to avoid unnecessary OF interrupts.
In addition, the S-mode SCOUNTEROF only have OF bit set when the related
bits of MCOUNTERWEN is set, so also configure MCOUNTERWEN to allow kernel
to access valid SCOUNTEROF.
Signed-off-by: Haijiao Liu <haijiao.liu@sophgo.com>
Co-authored-by: Inochi Amaoto <inochiama@outlook.com>
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Tested-by: Samuel Holland <samuel@sholland.org>
When detecting features of PMU, the hpm counter may be written to some
value, this will cause some unexpected behavior in some cases. So ensure
the hpm counter is updated before starting the counter and the related
interrupt.
Signed-off-by: Haijiao Liu <haijiao.liu@sophgo.com>
Co-authored-by: Inochi Amaoto <inochiama@outlook.com>
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Tested-by: Samuel Holland <samuel@sholland.org>
The previous definition had the assumption that the machine word length
is equal to the word length of LONG. Remove this assumption and add a
static check to prevent errors in subsequent modifications.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
As the the "Console Putchar" extension is already legacy and may
be removed in the furture. So replace it with the SBI v2.0 "DBCN"
extension.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
After supporting noncontigous hpm event and counters in opensbi, the
number of hpm counters can be calculated by the mhpm_mask. So this field
is unnecessary and can be removed to save some space.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
grep (at least my version, grep-3.8-3.fc38.x86_64) warns with
"grep: warning: stray \ before -". Fix the warning by making
the command line input to grep less ambiguous.
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
This adds the support for ISA extension smcntrpmf. When some inhibit flags
are set by a lower privilege mode for new CSRs added by smcntrpmf, OpenSBI
sets the appropriate values correspondingly.
Signed-off-by: Kaiwen Xue <kaiwenx@andrew.cmu.edu>
Signed-off-by: Kaiwen Xue <kaiwenx@rivosinc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Attempting to build OpenSBI with clang 16 and the following command:
$ make LLVM=1 PLATFORM=generic
Results in the following error:
AS platform/generic/firmware/fw_dynamic.o
/tmp/fw_dynamic-d000a6.s:429:9: error: symbol '_fw_start' can not be undefined in a subtraction expression
.dword _fw_rw_start - _fw_start
Work around this issue by eliminating the __fw_rw_offset variable and
performing the offset calculation at run-time instead. This takes
advantage of the fact that the a4 register contains the value of
_fw_start.
Signed-off-by: Mitchell Horne <mhorne@FreeBSD.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
Cycle and instructions are hardware events instead of firmware ones. Fix
the typo in the name of this function.
Signed-off-by: Kaiwen Xue <kaiwenx@andrew.cmu.edu>
Signed-off-by: Kaiwen Xue <kaiwenx@rivosinc.com>
Reviewed-by: Anup patel <anup@brainfault.org>
Currently, the fdt_parse_isa_extensions() tries to parse the ISA
string once for each HART. This ISA string parsing can fail for
secondary HARTs if the FDT memory is already overwritten by the
supervisor OS.
To tackle this issue, we improve the fdt_parse_isa_extensions()
implementation to pre-parse ISA string for all HARTs during
cold boot.
Fixes: d72f5f1747 ("lib: utils: Add detection of Smepmp from ISA
string in FDT")
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Tested-By: Mayuresh Chitale<mchitale@ventanamicro.com>
Platforms may implement hpm events/counters non contiguously but the current
implementation assumes them to be always contigous. Add a bitmap that
captures the hpm events/counters as implemented in the hardware and use
it to set the max limit of hardware counters visible to the OS. Counters
not implemented in the hardware can't be used by the OS because those
wont be described in the DT.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Nowadays, most of the editor use files or directories begin with dot to
store some settings. So let git ignore these files and directories to
reduce potential mistakes.
Add dot match to ignore any editor file and there are two exceptions:
- .gitignore
- .clang-format
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The functionality of SiFive Test reset driver is easily available
through Syscon reset driver so let us remove the SiFive Test driver.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Let us have common FDT based reset driver for syscon reboot and
poweroff. The device tree bindings for syscon reboot and poweroff
are already available in the Linux kernel sources.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Let us add a simple FDT based system regmap driver which follows the
device tree bindings already defined in the Linux kernel.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Xiang W <wxjstz@126.com>
We add a simple FDT based regmap framework which is built on top of
generic regmap library. The phandle of FDT regmap DT node is treated
as unique regmap ID. The FDT based regmap drivers will be probed
on-demand from fdt_regmap_get_by_phandle() and fdt_regmap_get()
called by the regmap client drivers.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Xiang W <wxjstz@126.com>
We add generic regmap access library which is independent of
hardware description format (FDT or ACPI). The OpenSBI platform
support or regmap drivers can register regmap instances which
can be discovered by different regmap clients based on the
unique ID of regmap instances.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Xiang W <wxjstz@126.com>
The "driver" pointer in struct i2c_adapter is not used anywhere
so let us remove it.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Because the CSR names in the spec are mseccfg and mseccfgh. Remove
CSR_MSECCFG_LOWER and CSR_MSECCFG_UPPER and directly define
CSR_MSECCFG and CSR_MSECCFGH.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
commit 68e66106120f ("SUSP: Add SBI_ERR_DENIED") of the SBI spec adds
a new error code, SBI_ERR_DENIED, which is returned when entry criteria
has not be meant. Update the system suspend implementation to return
this error when it has detected that not all harts are in the STOPPED
state.
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
With Smepmp enabled, it is necessary for shared memory from
S/U mode to be mapped/unmapped before and after read/write
of the memory region. This patch maps the debug console
shared memory before accessing it.
Signed-off-by: Himanshu Chauhan <hchauhan@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
When Smepmp is enabled, M-mode will need to map/unmap the
shared memory before it can read/write to it. This patch
adds functions to create dynamic short-lived mappings.
Signed-off-by: Himanshu Chauhan <hchauhan@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
- If Smepmp is enabled, the access flags of an entry are determined based on
truth table defined in Smepmp.
- First PMP entry (index 0) is reserved.
- Existing boot PMP entries start from index 1.
- Since enabling Smepmp revokes the access privileges of the M-mode software
on S/U-mode region, first PMP entry is used to map/unmap the shared memory
between M and S/U-mode. This allows a temporary access window for the M-mode
software to read/write to S/U-mode memory region.
Signed-off-by: Himanshu Chauhan <hchauhan@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Configure PMP at last when all other initializations have been done.
Because if SMEPMP is detected, M-mode access to the S/U space will be
rescinded.
Signed-off-by: Himanshu Chauhan <hchauhan@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Since pmp entries have implicit priority on index, previous entries will
deny access to SU on M-mode region. Also, M-mode will not have access to
SU region while previous entries will allow access to M-mode regions.
Signed-off-by: Himanshu Chauhan <hchauhan@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
- Add function to parse ISA string in FDT.
- Set Smepmp feature bit in extensions if "smepmp" string is found in ISA string.
Signed-off-by: Himanshu Chauhan <hchauhan@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Smepmp specification defines a truth table based on which the access is allowed to
different modes. This patch adds different flags based on this truth table.
Signed-off-by: Himanshu Chauhan <hchauhan@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
- Add a function to disable a given PMP entry.
- Add a function to check if a given entry is disabled.
Signed-off-by: Himanshu Chauhan <hchauhan@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Currently, we see following compile error in the designeware GPIO driver
for RV32 systems:
lib/utils/gpio/fdt_gpio_designware.c:115:20: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
115 | chip->dr = (void *)addr + (bank * 0xc);
| ^
lib/utils/gpio/fdt_gpio_designware.c:116:21: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
116 | chip->ext = (void *)addr + (bank * 4) + 0x50;
We fix the above error using an explicit type-cast to 'unsigned long'.
Fixes: 7828eebaaa ("gpio/desginware: add Synopsys DesignWare APB GPIO support")
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Fix special case: sbi_snprintf(out, out_len, ...) when out_len equal
1, The previous code will not fill the buffer with any char.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
A single scan of the format char may add multiple characters to the
tbuf, causing a buffer overflow. You should check if tbuf is full in
printc so that it does not cause a buffer overflow.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Because *out needs to reserve a byte to hold '\0', no more characters
should be added to the buffer when *out has one byte left, and the
buffer size *out_len should not be modified. this patch prevents
the correction of *out_len when *out_len is 1.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
When doing width = width - strlen(string) in prints there is no need
to consider the case that witdh may be less than 0. This is because
the code to do filling needs to be executed under the condition that
width > 0.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The information of sg/b/letbase can be obtained by the type character,
simplifying the parameter by passing the type directly.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The space flag is used to add a space before positive numbers, and
apostrophe is used to print the thousand separator. Add code to
ignore these two flags
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Adds + flags for print, prefixing positive numbers with + when this
flags is present
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Left alignment and padding '0' should not exist at the same time,
this patch skips padding.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The flags for print should be able to appear in any order. The
previous code required the order to be fixed.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Fix Priv spec version typo in commit d4b563c881 ("lib: sbi: Remove MCOUNTEREN
and SCOUNTEREN hart features").
At least Priv spec v1.11 is required for [m|s]counteren and mcountinhibit CSRs.
Fixes: d4b563c881 ("lib: sbi: Remove MCOUNTEREN and SCOUNTEREN hart features")
Signed-off-by: Ley Foon Tan <leyfoon.tan@starfivetech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The hart_pmu_get_allowed_bits() function detects implemented bits
of mhpm counters so let us rename this function accordingly.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Let us follow alphabetical order for HART ISA extension so that
it is simpler to maintain.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Recently ratified Zihpm ISA extension covers all [m]hpm* CSRs
so we add Zihpm as a HART ISA extension in OpenSBI.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Recently ratified Zicntr ISA extension covers cycle, time and
instret CSRs so we replace the "time" ISA extension with "zicntr"
ISA extension in OpenSBI.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Xiang W <wxjstz@126.com>
The cold_init() functions of ACLINT drivers should skip the HART
if sbi_hartid_to_scratch() returns NULL because we might be dealing
with a HART that is disabled in the device tree.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Add a driver for the Synopsys DesignWare APB GPIO IP block found in many
SoCs.
Signed-off-by: Ben Dooks <ben.dooks@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
On a misconfigured system we could access phs->active_events[] out of
bounds. Check that num_hw_ctrs is less or equal SBI_PMU_HW_CTR_MAX.
Addresses-Coverity-ID: 1566113 ("Out-of-bounds read")
Addresses-Coverity-ID: 1566114 ("Out-of-bounds write")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Do not ignore register A2 (high bits of physical address) in the dbcn
handler (RV64).
Signed-off-by: Gianluca Guida <gianluca@rivosinc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The fdt_reset_thead driver needs to modify the __reset_thead_csr_stub
text region for the secondary harts booting. After that, the
sbi_hart_pmp_configure may lock down the text region with M_READABLE &
M_EXECUTABLE attributes in the future. Currently, the M_READABLE &
M_EXECUtABLE have no effect on m-mode, the L-bit in pmpcfg csr is
useless for the current opensbi scenario. See:
Priv-isa-spec 3.7.1.2. Locking and Privilege Mode
When the L bit is clear, any M-mode access matching the PMP entry will
succeed; the R/W/X permissions apply only to S and U modes.
That's why current fdt_reset_thead could still work well after commit:
230278dcf1 ("lib: sbi: Add separate entries for firmware RX and RW
regions"). So this patch fixes up a fake bug for the M-mode permission
setting of the future.
Fixes: 230278dcf1 ("lib: sbi: Add separate entries for firmware RX and RW regions")
Link: http://lists.infradead.org/pipermail/opensbi/2023-June/005176.html
Reported-by: Jessica Clarke <jrtc27@jrtc27.com>
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Signed-off-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
After the loop to find the hartid is launched, assigning -1 to
index will fail in the subsequent compare instruction bge. Fix
This.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
This reverts commit 6966ad0abe ("platform/lib: Allow the OS to map the
regions that are protected by PMP").
It was thought at the time of this commit that allowing the kernel to map
PMP protected regions was safe but it is actually not: for example, the
hibernation process will try to access any linear mapping page and then
will fault on such mapped PMP regions [1]. Another issue is that the
device tree specification [2] states that a !no-map region must be
declared as EfiBootServicesData/Code in the EFI memory map which would make
the PMP protected regions reclaimable by the kernel. And to circumvent
this, RISC-V edk2 diverges from the DT specification to declare those
regions as EfiReserved.
The no-map attribute was removed to allow the kernel to use hugepages
larger than 2MB to map the linear mapping to improve the performance but
actually a recent talk from Mike Rapoport [3] stated that the
performance benefit was marginal.
For all those reasons, let's mark all the PMP protected regions as "no-map".
[1] https://lore.kernel.org/linux-riscv/CAAYs2=gQvkhTeioMmqRDVGjdtNF_vhB+vm_1dHJxPNi75YDQ_Q@mail.gmail.com/
[2] "3.5.4 /reserved-memory and UEFI" https://github.com/devicetree-org/devicetree-specification/releases/download/v0.4-rc1/devicetree-specification-v0.4-rc1.pdf
[3] https://lwn.net/Articles/931406/
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Over-time a lot of organizations and individuals have contributed to
the OpenSBI project so let us add copyright RISC-V International to
respect the contributions from all RISC-V members.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
We do have an official OpenSBI logo which was designed few months ago
and was also approved by RISC-V International. Lets add this logo
under docs and also use it in the top-level README.md
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Instead of using a global array indexed by hartid, we should use
scratch space to save per-HART IMSIC pointer and IMSIC file number.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
The imsic_map_hartid_to_data() already checks hartid before using
so we don't need to check in imsic_update_hartid_table().
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Instead of using a global array indexed by hartid, we should use
scratch space to save per-HART PLIC pointer and PLIC context numbers.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Instead of using a global array indexed by hartid, we should use
scratch space to save per-HART MTIMER pointer.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Instead of using a global array indexed by hartid, we should use
scratch space to save per-HART MSWI pointer.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Let's use heap allocation in FDT domain parsing instead of using
a fixed size global array.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Let's use heap allocation in ACLINT MTIMER driver instead of using
a fixed size global array.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Let's use heap allocation in PLIC, APLIC, and IMSIC irqchip drivers
instead of using a fixed size global array.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Let's use heap allocation in ACLINT MSWI driver instead of using
a fixed size global array.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Let's use heap allocation in DesignWare and SiFive I2C drivers
instead of using a fixed size global array.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Let's use heap allocation in SiFive and Starfive GPIO drivers
instead of using a fixed size global array.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Instead of using a global array indexed by hartid, we should use
scratch space to save per-HART domain pointer.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Let's use heap allocation in root domain creation instead of using
a fixed size global array.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Instead of using a global array for per-HART PMU state, we should
use heap to on-demand allocate per-HART PMU state when the HART
is initialized in cold boot or warm boot path.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
The scratch space being a scarce resource so let us print it's
size and usage at boot time.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
We provide simple heap allocator to manage the heap space provided
by OpenSBI firmware and platform.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
We extend struct sbi_platform and struct sbi_scratch to allow platforms
specify the heap size to the OpenSBI firmwares. The OpenSBI firmwares
will use this information to determine the location of heap and provide
heap base address in per-HART scratch space.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reading and writing a data type in scratch space is a very common
use-case so let us add related helper macros in sbi_scratch.h.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
The spec says sbi_system_suspend() will return SBI_ERR_INVALID_PARAM
when "sleep_type is reserved or is platform-specific and unimplemented"
and SBI_ERR_NOT_SUPPORTED when sleep_type "is not reserved and is
implemented, but the platform does not support it due to one or more
missing dependencies." Ensure SBI_ERR_INVALID_PARAM is returned for
reserved sleep types and that the system suspend driver can choose
which of the two error types to return itself by returning an error
from its check function rather than a boolean.
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The parameter checks in aclint_mswi_cold_init() don't guard against a
buffer overrun.
mswi_hartid2data is defined as an array of SBI_HARTMASK_MAX_BITS entries.
The current check allows
mswi->hart_count = ACLINT_MSWI_MAX_HARTS
mswi->first_hartid = SBI_HARTMASK_MAX_BITS - 1.
With these values mswi_hartid2data will be accessed at index
SBI_HARTMASK_MAX_BITS + SBI_HARTMASK_MAX_BITS - 2.
We have to check the sum of mswi->first_hartid and mswi->hart_count.
Furthermore mswi->hart_count = 0 would not make much sense.
Addresses-Coverity-ID: 1529705 ("Out-of-bounds write")
Fixes: 5a049fe1d6 ("lib: utils/ipi: Add ACLINT MSWI library")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
A final check of all DT nodes does not necessarily find a match, so
SBI_ENODEV needs to be returned. Optimize removal of current_driver.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
console is not a required peripheral. So it should return success when
the console does not exist.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Adds the `-L` flag (follow symlinks) to the `cp` commands used to
install `libsbi.a` and `include/sbi/*`.
This should make no difference in regular compilation. However,
it does make a difference when compiling with bazel. Namely,
bazel's sandboxing will turn all the source files into symlinks.
After installation with `cp` the destination files will be
symlinks pointing to the sandbox symlinks. As the sandbox files
are removed when compilation ends, the just-copied symlinks
become dangling symlinks.
The resulting include files will be
unusable due to the dangling symlink issues. Adding `-L` when
copying ensures that the files obtained by executing the `install`
targets are always dereferenced to files, rather than symlinks,
eliminating this issue.
Signed-off-by: Filip Filmar <fmil@google.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
With the introduction of the register_extensions callback the
range members (extid_start and extid_end) may now change and it
has become a bit subtle as to when a probe function should be
implemented. Document all the members and their relationship to
the register_extensions callback.
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
When a probe implementation just returns zero for not available and
one for available then we don't need it, as the extension won't be
registered at all if it would return zero and the Base extension
probe function will already set out_val to 1 if not probe function
is implemented. Currently all probe functions only return zero or
one, so remove them all.
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
No need to do a fully comprehensive count, just find a supported reset
or suspend type
Signed-off-by: Xiang W <wxjstz@126.com>
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
When an extension implements a probe function it means there's a
chance that the extension is not available. Use this function in the
register_extensions callback to determine if the extension should be
registered at all. Where the probe implementation is simple, just
open code the check.
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The absence of a probe implementation means that the extension is
always available. Remove the implementation for the PMU extension,
which does no checking, and indeed even has a comment saying it's
always available.
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The vendor extension ID range is large, but at runtime at most
a single ID will be available. Narrow the range in the
register_extensions callback. After narrowing, we no longer
need to check that the extension ID is correct in the other
callbacks, as those callbacks will never be invoked with
anything other than the single ID.
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Rather than registering all extensions on their behalf in
sbi_ecall_init(), introduce another extension callback and
invoke that instead. For now, implement each callback by
simply registering the extension, which means this patch
has no intended functional change. In later patches, extension
callbacks will be modified to choose when to register and to
possibly narrow the extension ID range prior to registering.
When an extension range needs to remove IDs, leaving gaps, then
multiple invocations of sbi_ecall_register_extension() may be
used. In summary, later patches for current extensions and the
introductions of future extensions will use the new callback to
ensure that only valid extension IDs from the initial range,
which are also available, will be registered.
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
We have redundant semicolon at quite a few places so let's remove it.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Since sbi_pmu_init is called after sbi_console_init,
the sbi_printf can be called when sbi_pmu_init fails.
Signed-off-by: Tan En De <ende.tan@starfivetech.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
The legacy console getchar SBI call returns character value in
the sbiret.error field so the "SBI_SUCCESS < ret" check in
sbi_ecall_handler() results in unwanted error prints for the
legacy console getchar SBI call. Let's suppress these unwanted
error prints.
Fixes: 67b2a40892 ("lib: sbi: sbi_ecall: Check the range of
SBI error")
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
As per the SBI specification, we should "unconditionally select the first
counter from the set of counters specified by the counter_idx_base and
counter_idx_mask", so implement this behaviour.
Suggested-by: Atish Patra <atishp@atishpatra.org>
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Those events are enabled by default and should not be reset afterwards
since when using SBI_PMU_CFG_FLAG_SKIP_MATCH, it leads to unaccessible
counters after the first use.
Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
The codes currently skip the very first relocation entry, but later
reference the elements in the relocation entry using minus offsets.
Change to use positive offsets so that there is no need to skip the
first relocation entry.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Xiang W <wxjstz@126.com>
I/O Coherence Port (IOCP) provides an AXI interface for connecting
external non-caching masters, such as DMA controllers. The accesses
from IOCP are coherent with D-Caches and L2 Cache.
IOCP is a specification option and is disabled on the Renesas RZ/Five
SoC (which is based on Andes AX45MP core) due to this reason IP blocks
using DMA will fail.
As a workaround for SoCs with IOCP disabled CMO needs to be handled by
software. Firstly OpenSBI configures the memory region as
"Memory, Non-cacheable, Bufferable" and passes this region as a global
shared dma pool as a DT node. With DMA_GLOBAL_POOL enabled all DMA
allocations happen from this region and synchronization callbacks are
implemented to synchronize when doing DMA transactions.
SBI_EXT_ANDES_IOCP_SW_WORKAROUND checks if the IOCP errata should be
applied to handle cache management.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Yu Chien Peter Lin <peterlin@andestech.com>
When tlb_fifo is full, it will wait and affect the ipi update to
other harts. This patch is optimized.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Tested-by: Anup Patel <anup@brainfault.org>
tlb_process_count is only used when count=1, so refactor to
tlb_process_once and add the return value to be reused in
tlb_process
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Tested-by: Anup Patel <anup@brainfault.org>
The original sbi_ipi will be processed by hart by hart, after optimization,
send ipi first and finally wait together.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Tested-by: Anup Patel <anup@brainfault.org>
Originally, the process and sync of sbi_tlb need to wait for each other.
Evasion by atomic addition and subtraction.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Tested-by: Anup Patel <anup@brainfault.org>
fdt_reserved_memory_fixup() uses filtered_order[PMP_COUNT]. The index
must not reach PMP_COUNT.
Fixes: 199189bd1c ("lib: utils: Mark only the largest region as reserved in FDT")
Addresses-Coverity-ID: 1536994 ("Out-of-bounds write")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
When using `PLATFORM=generic` defaults, the kernel is loaded at
`FW_JUMP_ADDR`, and the FDT is loaded at `FW_JUMP_FDT_ADDR.
Therefore, the maximum kernel size before `FW_JUMP_FDT_ADDR` must
be increased is `$(( FW_JUMP_FDT_ADDR - FW_JUMP_ADDR ))`.
The example calculation assumes `rv64`, and is wrong to boot
(off by 0x200000). Fix it and update it for the general case.
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Xiang W <wxjstz@126.com>
The bits encoded in event_idx[19:16] indicate the event type, with
an offset of 16 instead of 20.
Fixes: 13d40f21d5 ("lib: sbi: Add PMU support")
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Implement SBI CPPC extension. This extension is only available when
OpenSBI platform provides a CPPC device to generic library.
Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
If mip.SEIP bit is not cleared then on HiFive Unmatched board it causes
spurious external interrupts. This breaks the boot up of HiFive Unmatched
board. Hence it is required to bring the mip CSR to a known state during
hart init and avoid spurious interrupts.
Fixes: d9e7368 ("firmware: Not to clear all the MIP")
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
It possible that a platform supports hart hotplug (i.e. both hart_start
and hart_stop callbacks available) and all harts are start simultaneously
at platform boot-time. In this situation, the sbi_hsm_hart_start() will
call hsm_device_hart_start() for secondary harts at platform boot-time
which will fail because secondary harts were already started.
To fix above, we call hsm_device_hart_start() from sbi_hsm_hart_start()
only when entry_count is same as init_count for the secondary hart.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
We introduce sbi_entry_count() function which counts the number
of times a HART enters OpenSBI via cold-boot or warm-boot path.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Because firmware is split into rw/rx segments, it cannot be recorded
by a root_fw_region. This problem is solved by adding a flag
fw_region_inited to sbi_domain.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Himanshu Chauhan <hchauhan@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Since commit 50d4fde1c5 ("lib: Remove redundant sbi_platform_ipi_clear()
calls"), the IPI sent from the boot hart in wake_coldboot_harts() is not
cleared in the secondary harts until they reach sbi_ipi_init(). However,
sbi_hsm_init() and sbi_hsm_hart_wait() are called earlier, so a secondary
hart might enter sbi_hsm_hart_wait() with an already pending IPI.
sbi_hsm_hart_wait() makes sure the hart leaves the loop only when it is
actually ready, so a pending unrelated IPI should not cause safety issues.
However, it might be inefficient on certain hardware, because it prevents
"wfi" from stalling the hart even if the hardware supports this, making the
hart needlessly spin in a "busy-wait" loop.
This behaviour can be observed, for example, in a QEMU VM (QEMU 7.2.0) with
"-machine virt" running a Linux guest. Inserting delays in
sbi_hsm_hart_start() allows reproducing the issue more reliably.
The comment in wait_for_coldboot() suggests that the initial IPI is needed
in the warm resume path, so let us clear it before init_warm_startup()
only.
To do this, sbi_ipi_raw_clear() was created similar to sbi_ipi_raw_send().
Signed-off-by: Evgenii Shatokhin <e.shatokhin@yadro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
When a boot hart executes sbi_hsm_hart_start() to start a secondary hart,
next_arg1, next_addr and next_mode for the latter are stored in the scratch
area after the state has been set to SBI_HSM_STATE_START_PENDING.
The secondary hart waits in the loop with wfi() in sbi_hsm_hart_wait() at
that time. However, "wfi" instruction is not guaranteed to wait for an
interrupt to be received by the hart, it is just a hint for the CPU.
According to RISC-V Privileged Architectures spec. v20211203, even an
implementation of "wfi" as "nop" is legal.
So, the secondary might leave the loop in sbi_hsm_hart_wait() as soon as
its state has been set to SBI_HSM_STATE_START_PENDING, even if it got no
IPI or it got an IPI unrelated to sbi_hsm_hart_start(). This could lead to
the following race condition when booting Linux, for example:
Boot hart (#0) Secondary hart (#1)
runs Linux startup code waits in sbi_hsm_hart_wait()
sbi_ecall(SBI_EXT_HSM,
SBI_EXT_HSM_HART_START,
...)
enters sbi_hsm_hart_start()
sets state of hart #1 to START_PENDING
leaves sbi_hsm_hart_wait()
runs to the end of init_warmboot()
returns to scratch->next_addr
(next_addr can be garbage here)
sets next_addr, etc. for hart #1
(no good: hart #1 has already left)
sends IPI to hart #1
(no good either)
If this happens, the secondary hart jumps to a wrong next_addr at the end
of init_warmboot(), which leads to a system hang or crash.
To reproduce the issue more reliably, one could add a delay in
sbi_hsm_hart_start() after setting the hart's state but before sending
IPI to that hart:
hstate = atomic_cmpxchg(&hdata->state, SBI_HSM_STATE_STOPPED,
SBI_HSM_STATE_START_PENDING);
...
+ sbi_timer_mdelay(10);
init_count = sbi_init_count(hartid);
rscratch->next_arg1 = arg1;
rscratch->next_addr = saddr;
The issue can be reproduced, for example, in a QEMU VM with '-machine virt'
and 2 or more CPUs, with Linux as the guest OS.
This patch moves writing of next_arg1, next_addr and next_mode for the
secondary hart before setting its state to SBI_HSM_STATE_START_PENDING.
In theory, it is possible that two or more harts enter sbi_hsm_hart_start()
for the same target hart simultaneously. To make sure the current hart has
exclusive access to the scratch area of the target hart at that point, a
per-hart 'start_ticket' is used. It is initially 0. The current hart tries
to acquire the ticket first (set it to 1) at the beginning of
sbi_hsm_hart_start() and only proceeds if it has successfully acquired it.
The target hart reads next_addr, etc., and then the releases the ticket
(sets it to 0) before calling sbi_hart_switch_mode(). This way, even if
some other hart manages to enter sbi_hsm_hart_start() after the ticket has
been released but before the target hart jumps to next_addr, it will not
cause problems.
atomic_cmpxchg() already has "acquire" semantics, among other things, so
no additional barriers are needed in hsm_start_ticket_acquire(). No hart
can perform or observe the update of *rscratch before setting of
'start_ticket' to 1.
atomic_write() only imposes ordering of writes, so an explicit barrier is
needed in hsm_start_ticket_release() to ensure its "release" semantics.
This guarantees that reads of scratch->next_addr, etc., in
sbi_hsm_hart_start_finish() cannot happen after 'start_ticket' has been
released.
Signed-off-by: Evgenii Shatokhin <e.shatokhin@yadro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Move them into sbi_hsm_hart_start_finish() and sbi_hsm_hart_resume_finish()
to make them easier to manage.
This will be used by subsequent patches.
Suggested-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Evgenii Shatokhin <e.shatokhin@yadro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Platform specific firmware event handler may leverage the hartid to program
per hart specific registers for a given counter.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Add fw_counter_write_value API for platform specific firmware events
which separates setting the counter's initial value from starting the
counter. This is required so that the fw_event_data array can be reused
to save the event data received.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
For all platform specific firmware event operations use the dedicated
event code (0xFFFF) when matching against the input firmware event.
Furthermore save the real platform specific firmware event code received as
the event data for future use.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Update fw_event_validate_code, fw_counter_match_code and fw_counter_start
ops which used a 32 bit event code to use the 64 bit event data instead.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Rename and reuse fw_counter_value array to save both the counter values
for the SBI firmware events and event data for the SBI platform specific
firmware events.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
We reserve space for SBI implementation specific custom firmware
events which can be used by M-mode firmwares and HS-mode hypervisors
for their own use. This reserved space is intentionally large to
ensure that SBI implementation has enough space to accommodate
platform specific firmware events as well.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
To support 64 bit firmware counters on RV32 systems, we implement
sbi_pmu_counter_fw_read_hi() which returns the upper 32 bits of
the firmware counter value. On RV64 (or higher) systems, this
function will always return zero.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
This patch adds a callback to fetch the number of bits implemented for a
custom firmware counter. If the callback fails or is not implemented then
width defaults to 63.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The Cadence driver does not use the RX byte status feature and hence can
be advertised to be compatible with cdns,uart-r1p8 as well.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
add reboot and poweroff support. The whole reboot and shutdown
pm op includes shutdown jh7110 pmu device power domain
and access on board pmic register through I2C.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Starfive JH7110 I2C IP is synopsys designware.
Minimum StarFIve I2C driver to read/send bytes over I2C bus.
This allows querying information and perform operation of onboard PMIC,
as well as power-off and reset.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Add a new make command line option "make DEBUG=1" to prevent compiler
optimizations using -O2.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
When the system-suspend-test property is present in the domain config
node as shown below, implement system suspend with a simple 5 second
delay followed by a WFI. This allows testing system suspend when the
low-level firmware doesn't support it.
/ {
chosen {
opensbi-domains {
compatible = "opensbi,domain,config";
system-suspend-test;
};
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Fill the implementation of the system suspend ecall. A platform
implementation of the suspend callbacks is still required for this
to do anything.
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Only privileged domains should be allowed to suspend the entire
system. Give the root domain this property by default and allow
other domains to be given the property by specifying it in the
DT.
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Add the SUSP extension probe and ecall support, but for now the
system suspend function is just a stub.
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
A coming patch can make use of a few internal hsm functions if
we export them.
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
While non-retentive suspend is not allowed for M-mode, the comment
at the top of sbi_hsm_hart_suspend() implied suspend wasn't allowed
for M-mode at all. Move the comment above the mode check which is
inside a suspend type is non-retentive check.
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
HSM functions define when SBI_ERR_INVALID_PARAM should be returned.
Ensure it's not used for reasons that don't meet the definitions by
using the catch-all code, SBI_ERR_FAILED, for those reasons instead.
Also, in one case sbi_hart_suspend() may have returned SBI_ERR_DENIED,
which isn't defined for that function at all. Use SBI_ERR_FAILED for
that case too.
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
When a state change fails there's no need to restore the original
state as it remains the same.
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Remove some redundant code by creating an invalid state detection
macro.
No functional change intended.
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
commit 3e2f573e70 ("lib: utils: Disallow non-root domains from adding M-mode regions")
added access permission check in __fdt_parse_region(). With the
existing DT example in the doc OpenSBI won't boot anymore.
Let's update the DT example so that it can work out of the box.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
The region access permission check in __fdt_parse_region() can be
simplified as masking SBI_DOMAIN_MEMREGION_{M,SU}_ACCESS_MASK is
enough.
While we are here, update the confusing comments to match the codes.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
On the Renesas RZ/Five SoC by default we want to configure 128MiB of memory
ranging from 0x58000000 as a non-cacheable + bufferable region in the PMA
and populate this region as PMA reserve DT node with shared DMA pool and
no-map flags set so that Linux drivers requesting any DMA'able memory go
through this region.
PMA node passed to the above stack:
reserved-memory {
#address-cells = <2>;
#size-cells = <2>;
ranges;
pma_resv0@58000000 {
compatible = "shared-dma-pool";
reg = <0x0 0x58000000 0x0 0x08000000>;
no-map;
linux,dma-default;
};
};
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
I/O Coherence Port (IOCP) provides an AXI interface for connecting
external non-caching masters, such as DMA controllers. The accesses
from IOCP are coherent with D-Caches and L2 Cache.
IOCP is a specification option and is disabled on the Renesas RZ/Five
SoC due to this reason IP blocks using DMA will fail.
The Andes AX45MP core has a Programmable Physical Memory Attributes (PMA)
block that allows dynamic adjustment of memory attributes in the runtime.
It contains a configurable amount of PMA entries implemented as CSR
registers to control the attributes of memory locations in interest.
Below are the memory attributes supported:
* Device, Non-bufferable
* Device, bufferable
* Memory, Non-cacheable, Non-bufferable
* Memory, Non-cacheable, Bufferable
* Memory, Write-back, No-allocate
* Memory, Write-back, Read-allocate
* Memory, Write-back, Write-allocate
* Memory, Write-back, Read and Write-allocate
More info about PMA (section 10.3):
Link: http://www.andestech.com/wp-content/uploads/AX45MP-1C-Rev.-5.0.0-Datasheet.pdf
As a workaround for SoCs with IOCP disabled CMO needs to be handled by
software. Firstly OpenSBI configures the memory region as
"Memory, Non-cacheable, Bufferable" and passes this region as a global
shared dma pool as a DT node. With DMA_GLOBAL_POOL enabled all DMA
allocations happen from this region and synchronization callbacks are
implemented to synchronize when doing DMA transactions.
Example PMA region passed as a DT node from OpenSBI:
reserved-memory {
#address-cells = <2>;
#size-cells = <2>;
ranges;
pma_resv0@58000000 {
compatible = "shared-dma-pool";
reg = <0x0 0x58000000 0x0 0x08000000>;
no-map;
linux,dma-default;
};
};
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
As-per the SBI specification, the lower 24bits of the SBI vendor
extension id is same as lower 24bits of the mvendorid CSR.
We update the SBI vendor extension id checking based on above.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
According to the description in "riscv-state-enable[0]", to access
h/scontext in S-Mode, we need to enable the 57th bit.
If it is not enabled, an "illegal instruction" error will occur.
Link: a28bfae443/content.adoc [0]
Signed-off-by: Nylon Chen <nylon.chen@sifive.com>
Reviewed-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
In docs/firmware/fw.md, there's a configuration parameter called
FW_TEXT_ADDR, which actually should be FW_TEXT_START, so fix it.
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
When building with GCC-10 or older versions, it throws the following
error:
CC-DEP platform/generic/lib/utils/fdt/fdt_fixup.dep
CC platform/generic/lib/utils/fdt/fdt_fixup.o
lib/utils/fdt/fdt_fixup.c: In function 'fdt_reserved_memory_fixup':
lib/utils/fdt/fdt_fixup.c:376:2: error: label at end of compound statement
376 | next_entry:
| ^~~~~~~~~~
Remove the goto statement.
Resolves: https://github.com/riscv-software-src/opensbi/issues/288
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
In sbi_domain_finalize(), when locating the coldboot hart's domain,
the coldboot hart's scratch->arg1 will be overwritten by the domain
configuration. However scratch->arg1 holds the FDT address of the
coldboot hart, and is still being accessed by fdt_get_address() in
later boot process. scratch->arg1 could then contain completely
garbage and lead to a crash.
To fix this, we change fdt_get_address() to return root domain's
next_arg1 as the FDT pointer.
Resolves: https://github.com/riscv-software-src/opensbi/issues/281
Fixes: b1678af210 ("lib: sbi: Add initial domain support")
Reported-by: Marouene Boubakri <marouene.boubakri@nxp.com>
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
The code calls various macros from riscv_asm.h which is not directly
included. Fix such dependency.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
The code calls various macros from riscv_asm.h and sbi_scratch.h
which are not directly included. Fix such dependency.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
The code calls sbi_scratch_thishart_ptr() from sbi_scratch.h which
is not directly included. Fix such dependency.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
The sbi_printf() is slow for semihosting because it prints one
character at a time. To speed-up sbi_printf() for semihosting,
we use a temporary buffer and nputs().
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
We add console_puts() callback in the console device which allows
console drivers (such as semihosting) to implement a specialized
way to output character string.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
We implement SBI debug console extension as one of the replacement
SBI extensions. This extension is only available when OpenSBI platform
provides a console device to generic library.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
The BSWAPx() macros won't do any swapping for big-endian host
because the EXTRACT_BYTE() macro will pickup bytes in reverse
order. Also, the EXTRACT_BYTE() will generate compile error
for constants.
To fix this, we get remove the EXTRACT_BYTE() macro and re-write
BSWAPx() using simple mask and shift operations.
Fixes: 09b34d8cca ("include: Add support for byteorder/endianness
conversion")
Reported-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
If any variable/memory-location follows certain
endianness then its important to annotate it properly
so that proper conversion can be done before read/write
from that variable/memory.
Also, use these new typedefs in libfdt_env.h for deriving
its own custom fdtX_t types
Signed-off-by: Rahul Pathak <rpathak@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
FDT follows big-endian and CPU can be little or big
endian as per the implementation.
libfdt_env.h defines function for conversion between
fdt and cpu byteorder according to the endianness.
Currently, libfdt_env.h defines custom byte swapping
macros and then undefines them. Instead, use the generic
endianness conversion functions
Signed-off-by: Rahul Pathak <rpathak@ventanamicro.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Since we don't currently create these, changes to fw_base.ldS do not
cause the preprocessed fw_*.elf.ld files to be rebuilt, and thus
incremental builds can end up failing with missing symbols if crossing
the recent commits that introduced _fw_rw_offset and then replaced it
with _fw_rw_start.
Reported-by: Ben Dooks <ben.dooks@sifive.com>
Signed-off-by: Jessica Clarke <jrtc27@jrtc27.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
sbi_domain_for_each() requires domidx_to_domain_table[] to be
null-terminated. Allocate one extra element which will always
be null.
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
In commit 230278dcf, RX and RW regions were marked separately.
When the RW region grows (e.g. with more harts) and it isn't a
power-of-two, sbi_domain_memregion_init will upgrade the region
to the next power-of-two. This will make RX and RW both start
at the same base address, like so (with 64 harts):
Domain0 Region01 : 0x0000000080000000-0x000000008001ffff M: (R,X) S/U: ()
Domain0 Region02 : 0x0000000080000000-0x00000000800fffff M: (R,W) S/U: ()
This doesn't break the permission enforcement because of static
priorities in PMP but makes the kernel complain about the regions
overlapping each other. Like so:
[ 0.000000] OF: reserved mem: OVERLAP DETECTED!
[ 0.000000] mmode_resv0@80000000 (0x0000000080000000--0x0000000080020000) \
overlaps with mmode_resv1@80000000 (0x0000000080000000--0x0000000080100000)
To fix this warning, among the multiple regions having same base
address but different sizes, add only the largest region as reserved
region during fdt fixup.
Fixes: 230278dcf (lib: sbi: Add separate entries for firmware RX and RW regions)
Signed-off-by: Himanshu Chauhan <hchauhan@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
If we use the csr_write to restore the MIP, we may clear the SEIP.
In generic behavior of QEMU, if the pending bits of PLIC are set and we
clear the SEIP, the QEMU may not set it back immediately. It may cause
the interrupts won't be handled anymore until the new interrupts arrived
and QEMU set the bits back.
Signed-off-by: Nick Hu <nick.hu@sifive.com>
Signed-off-by: Jim Shu <jim.shu@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
In generic behavior of QEMU, if the pending bits of PLIC are still set and
we clear the SEIP, the QEMU may not set the SEIP back immediately and the
interrupt may not be handled anymore until the new interrupts arrived and
QEMU set the SEIP back which is a generic behavior in QEMU.
Signed-off-by: Nick Hu <nick.hu@sifive.com>
Signed-off-by: Jim Shu <jim.shu@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
It seems BFD just does totally nonsensical things for SHN_ABS symbols
when producing position-independent outputs (both -pie and -shared)
for various historical reasons, and so SHN_ABS symbols are still
subject to relocation as far as BFD is concerned (except AArch64,
which fixes it in limited cases that don’t apply here...).
The above affects the _fw_rw_offset provided through fw_base.ldS
linker script which results in OpenSBI firmware failing to boot
when loaded at an address different from FW_TEXT_START.
Fixes: c10e3fe5f9 ("firmware: Add RW section offset in scratch")
Signed-off-by: Jessica Clarke <jrtc27@jrtc27.com>
Reported-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Tested-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Tested-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Add D1's nonretentive suspend state to the devicetree so S-mode software
knows about it and can use it.
Latency and power measurements were taken on an Allwinner Nezha board:
- Entry latency was measured from the beginning of sbi_ecall_handler()
to before the call to wfi() in sun20i_d1_hart_suspend().
- Exit latency was measured from the beginning of sbi_init() to before
the call to sbi_hart_switch_mode() in init_warmboot().
- There was a 17.5 mW benefit from non-retentive suspend compared to
WFI, with a 170 mW cost during the 107 us entry/exit period. This
provides a break-even point around 1040 us. Residency includes entry
latency, so round this up to 1100 us.
- The hardware power sequence latency (after the WFI) is assumed to be
negligible, so set the wakeup latency to the exit latency.
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Since the availability and latency properties of CPU idle states depend
on the specific SBI HSM implementation, it is appropriate that the idle
states are added to the devicetree at runtime by that implementation.
This helper function adds a platform-provided array of idle states to
the devicetree, following the SBI idle state binding.
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Renesas RZ/Five RISC-V SoC has Instruction local memory and Data local
memory (ILM & DLM) mapped between region 0x30000 - 0x4FFFF. When a
virtual address falls within this range, the MMU doesn't trigger a page
fault; it assumes the virtual address is a physical address which can
cause undesired behaviours for statically linked applications/libraries.
To avoid this, add the ILM/DLM memory regions to the root domain region
of the PMPU with permissions set to 0x0 for S/U modes so that any access
to these regions gets blocked and for M-mode we grant full access (R/W/X).
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Add two entries for firmware in the root domain:
1. TEXT: fw_start to _fw_rw_offset with RX permissions
2. DATA: _fw_rw_offset to fw_size with RW permissions
These permissions are still not enforced from M-mode but lay
the ground work for enforcing them for M-mode. SU-mode don't
have any access to these regions.
Sample output:
Domain0 Region01 : 0x0000000080000000-0x000000008001ffff M: (R,X) S/U: ()
Domain0 Region02 : 0x0000000080020000-0x000000008003ffff M: (R,W) S/U: ()
Signed-off-by: Himanshu Chauhan <hchauhan@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Print the RW section offset when firmware base and size is
being printed.
Signed-off-by: Himanshu Chauhan <hchauhan@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Add the RW section offset, provided by _fw_rw_offset symbol,
to the scratch structure. This will be used to program
separate pmp entry for RW section.
Signed-off-by: Himanshu Chauhan <hchauhan@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Currently, the dynsym and reladyn sections are under RW data.
They are moved to the Read-only/Executable region.
Signed-off-by: Himanshu Chauhan <hchauhan@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Split the RO/RX and RW sections so that they can have
independent pmp entries with required permissions. The
split size is ensured to be a power-of-2 as required by
pmp.
_fw_rw_offset symbol marks the beginning of the data
section.
Signed-off-by: Himanshu Chauhan <hchauhan@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The commit 9e0ba090 introduced more fine grained permissions for memory
regions and did not update the fdt_reserved_memory_fixup() function. As
a result, the fdt_reserved_memory_fixup continued to use the older coarse
permissions which causes the reserved memory node to be not inserted
into the DT.
To fix the above issue, we correct the flags used for memory region
permission checks in the fdt_reserved_memory_fixup() function.
Fixes: 9e0ba090 ("include: sbi: Fine grain the permissions for M and SU modes")
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Add hart_start() and hart_stop() callbacks for the multi-core ae350
platform, it utilizes the ATCSMU to put the harts into power-gated
deep sleep mode. The programming sequence is stated as below:
1. Set the wakeup events to PCSm_WE
2. Set the sleep command to PCSm_CTL
3. Set the reset vector to HARTm_RESET_VECTOR_{LO|HI}
4. Write back and invalidate D-cache by executing the CCTL command L1D_WBINVAL_ALL
5. Disable I/D-cache by clearing mcache_ctl.{I|D}C_EN
6. Disable D-cache coherency by clearing mcache_ctl_.DC_COHEN
7. Wait for mcache_ctl.DC_COHSTA to be cleared to ensure the previous step is completed
8. Execute WFI
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
This patch adds atcsmu support for Andes AE350 platforms. The SMU
provides system management capabilities, including clock, reset
and power control based on power domain partitions.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Make use of generic warm-boot path when platform hart_stop callback
returns SBI_ENOTSUPP, in case certain hart can not turn off its
power domain, or it detects some error occured in power management
unit, it can fall through warm-boot flow and wait for interrupt in
sbi_hsm_hart_wait().
Also improves comment in sbi_hsm_hart_wait().
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The two referenced commits passed incorrect bounds to the PLIC save/
restore functions, causing out-of-bounds memory access. The functions
expect "num" to be the 1-based number of interrupt sources, equivalent
to the "riscv,ndev" devicetree property. Thus, "num" must be strictly
smaller than the 0-based size of the array storing the register values.
However, the referenced commits incorrectly passed in the unmodified
size of the array as "num". Fix this by reducing PLIC_SOURCES (matching
"riscv,ndev" on this platform), while keeping the same array sizes.
Addresses-Coverity-ID: 1530251 ("Out-of-bounds access")
Addresses-Coverity-ID: 1530252 ("Out-of-bounds access")
Fixes: 8509e46ca6 ("lib: utils/irqchip: plic: Ensure no out-of-bound access in priority save/restore helpers")
Fixes: 9a2eeb4aae ("lib: utils/irqchip: plic: Ensure no out-of-bound access in context save/restore helpers")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
Updated the various permissions bits available for domains
defined in DT node and restrictions on them.
Signed-off-by: Himanshu Chauhan <hchauhan@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Tested-by: Anup Patel <anup@brainfault.org>
The M-mode regions can only be added to the root domain. The non-root
domains shouldn't be able to add them from FDT.
Signed-off-by: Himanshu Chauhan <hchauhan@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Tested-by: Anup Patel <anup@brainfault.org>
With the finer permission semantics, the region access
permissions must be displayed separately for M and SU mode.
Signed-off-by: Himanshu Chauhan <hchauhan@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Tested-by: Anup Patel <anup@brainfault.org>
Use the fine grained permission bits to decide if the region
permissions are to be enforced on all modes. Also use the new
permission bits for deciding on R/W/X bits in pmpcfg register.
Signed-off-by: Himanshu Chauhan <hchauhan@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Tested-by: Anup Patel <anup@brainfault.org>
Split the permissions for M-mode and SU-mode. This would
help if different sections of OpenSBI need to be given
different permissions and if M-mode has different permisssions
than the SU-mode over a region.
Signed-off-by: Himanshu Chauhan <hchauhan@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Tested-by: Anup Patel <anup@brainfault.org>
The RISC-V convention for the privilege mode is capital letter, like
'M-mode', instead of 'm-mode'.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
'priv' argument of sbi_hsm_hart_start() and sbi_hsm_hart_suspend()
may mislead people to think it stands for 'privilege mode', but it
is not. Change it to 'arg1' to clearly indicate the a1 register.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
We add a generic platform override callback to allow platform specific
selection of cold boot HART.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
We add an optional cold_boot_allowed() platform callback which allows
platform support to decide which HARTs can do cold boot initialization.
If this platform callback is not available then any HART can do cold
boot initialization.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
commit 6dde43584f ("lib: utils/sys: Extend HTIF library to allow custom base address")
forgot to update do_tohost_fromhost() codes for RV32, which still
accesses the HTIF registers using the ELF symbol address directly.
Fixes: 6dde43584f ("lib: utils/sys: Extend HTIF library to allow custom base address")
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Tested-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
-N option coalesce all sections into single LOAD segment which causes
data and other sections to have executable permission causing warning
with new binutils ld 2.39.
New ld emits warning when any segment have all three permissions RWX.
ld.bfd: warning: test.elf has a LOAD segment with RWX permissions
ld.bfd: warning: fw_dynamic.elf has a LOAD segment with RWX permissions
ld.bfd: warning: fw_jump.elf has a LOAD segment with RWX permissions
ld.bfd: warning: fw_payload.elf has a LOAD segment with RWX permissions
This option was added in below commit -
commit: eeab92f242 ("Makefile: Convert to a more standard format")
Removing -N option allows to have text and rodata into one LOAD
segment and other sections into separate LOAD segment which prevents
RWX permissions on single LOAD segment. Here X == E
Current
LOAD 0x0000000000000120 0x0000000080000000 0x0000000080000000
0x000000000001d4d0 0x0000000000032ed8 RWE 0x10
-N removed
LOAD 0x0000000000001000 0x0000000080000000 0x0000000080000000
0x00000000000198cc 0x00000000000198cc R E 0x1000
LOAD 0x000000000001b000 0x000000008001a000 0x000000008001a000
0x00000000000034d0 0x0000000000018ed8 RW 0x1000
Signed-off-by: Rahul Pathak <rpathak@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Tested-by: Samuel Holland <samuel@sholland.org>
C language standard uses true/false for the boolean type.
Let's switch to that for better language compatibility.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
Since commit b28f070, it is possible for platforms to run perf monitoring
even if mcountinhibit is not supported. Sampling still won't be possible
though as it requires sscofpmf extension.
Update the docs to remove the restriction.
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
event-to-mhpmevent was deprecated and replaced by
riscv,event-to-mhpmevent, but a reference remains to the old name.
Replace it with the new one.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The first PMU binding example does not terminate properties with a ;,
which is invalid. Noticed while converting the binding to yaml.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
As we already added the quirk for lacking mtime register to MTIMER
driver, add T-Head C9xx CLINT compatible to it and wire the quirk.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Reviewed-by: Anup Patel <anup@brainfault.org>
T-Head developers surely have a different understanding of time CSR and
CLINT's mtime register with SiFive ones, that they did not implement
the mtime register at all -- as shown in openC906 source code, their
time CSR value is just exposed at the top of their processor IP block
and expects an external continous counter, which makes it not
overrideable, and thus mtime register is not implemented, even not for
reading. However, if CLINTEE is not enabled in T-Head's MXSTATUS
extended CSR, these systems still rely on the mtimecmp registers to
generate timer interrupts. This makes it necessary to implement T-Head
C9xx CLINT support in OpenSBI MTIMER driver, which skips implementing
reading mtime register and falls back to default code that reads time
CSR.
Add a quirk into MTIMER driver, which represents a mtime register is
lacking and time CSR value should be used instead.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Reviewed-by: Anup Patel <anup@brainfault.org>
Althoug the MTIMER part of a C9xx CLINT differs from a SiFive one, the
MSWI part is compliant.
Add T-Head C9xx CLINT compatible string to fdt_ipi_mswi code, sharing
the same codepath with SiFive CLINT.
Signed-off-by: Icenowy Zheng <uwu@icenowy.me>
Reviewed-by: Anup Patel <anup@brainfault.org>
Currently the context save/restore helpers writes/reads the provided
array using an index whose maximum value is determined by PLIC, which
potentially may disagree with the caller to these helpers.
Add a parameter to ask the caller to provide the size limit of the
array to ensure no out-of-bound access happens.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
plic->num_src holds the number of interrupt sources without interrupt
source 0 but the interrupt enable register includes a bit for the
interrupt source 0 in the first word.
Fixes: 415ecf28f7 ("lib: irqchip/plic: Add context save/restore helpers")
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Samuel Holland <samuel@sholland.org>
The number of interrupt enable register in words was once correct,
but was wrongly changed to have an off-by-one error since
commit 8c362e7d06 ("lib: irqchip/plic: Factor out a context init function").
Fixes: 8c362e7d06 ("lib: irqchip/plic: Factor out a context init function")
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Currently the priority save/restore helpers writes/reads the provided
array using an index whose maximum value is determined by PLIC, which
potentially may disagree with the caller to these helpers.
Add a parameter to ask the caller to provide the size limit of the
array to ensure no out-of-bound access happens.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
Add compatible string for Andestech NCEPLIC100 found on Renesas RZ/Five SoC
which is equipped with AX45MP AndesCore.
While at it drop the comma after the sentinel as it does not make sense to
have a comma after a sentinel, as any new elements must be added before the
sentinel.
dts example (Single-core AX45MP):
soc: soc {
....
plic: interrupt-controller@12c00000 {
compatible = "renesas,r9a07g043-plic", "andestech,nceplic100";
#interrupt-cells = <2>;
#address-cells = <0>;
riscv,ndev = <511>;
interrupt-controller;
reg = <0x0 0x12c00000 0 0x400000>;
clocks = <&cpg CPG_MOD R9A07G043_NCEPLIC_ACLK>;
power-domains = <&cpg>;
resets = <&cpg R9A07G043_NCEPLIC_ARESETN>;
interrupts-extended = <&cpu0_intc 11 &cpu0_intc 9>;
};
....
};
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Not all systems have bash at a fixed location like /bin/bash.
FreeBSD, for example, would typically have it at /usr/local/bin/bash.
When building OpenSBI on freebsd system, the build breaks.
Its advisable to use: #!/usr/bin/env bash
Signed-off-by: Himanshu Chauhan <hchauhan@ventanamicro.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
As per section 3.7.2 of RISC-V Privileged Specification,
PMP settings must be synchronized with the virtual memory
system after PMP settings have been written.
Signed-off-by: Himanshu Chauhan <hchauhan@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
If fdt_getprop() returns NULL, this indicates an error. In this case lenp
is set to an error code. But even if lenp = 0 we should not continue.
If fdt_getprop() returns a wider value than we expect this is a separate
error condition.
In both cases the device-tree is invalid.
Addresses-Coverity-ID: 1529703 ("Dereference after null check")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
For 'reg->order == __riscv_xlen' the term 'BIT(reg->order)' is undefined.
Addresses-Coverity-ID: 1529706 ("Bad bit shift operation")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
It makes sense to use fdt_match_node() instead of fdt_find_match()
in fw_platform_lookup_special() as we already have the start offset
to search from.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The andes-specific files have been moved to generic platform so we
can drop this line.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
Update compile option and platform compatible string for AE350 and
add it to the generic platform list.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
We move andes directory to platform/generic as the necessary fdt
drivers are available, the users can enable the console, timer, ipi,
irqchip and reset devices by adding device tree nodes stated in the
docs/platform/andes-ae350.md.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
The t3 register stores the address of _load_end. If relocation is not
required, it is unnecessary to calculate the address of _load_end.
This can reduce the operation time of two instructions.
Signed-off-by: Dongdong Zhang <zhangdongdong@eswincomputing.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
cpu_offset and cpu_intc_offset must be int to detect failed invocations of
fdt_node_offset_by_phandle() or fdt_parent_offset().
After determining cpu_offset we have to check this value and not
cpu_intc_offset.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
cpu_offset, cpu_intc_offset must be int to discover failed invocations of
fdt_node_offset_by_phandle() or fdt_parent_offset().
After determining cpu_offset we have to check this value and not
cpu_intc_offset.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
When order is equal to __riscv_xlen, the shift operation will not perform
any operation, which will cause reg->base & (BIT(reg->order) - 1) to always
be 0, and the condition has not been established.
This patch fixes this bug.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
If the path where this repo is located contains the platform name on
it, the original Makefile replaced its occurrences from the path making
it an invalid path. This commit prevents this behavior replacing only
the last part of the path as intended.
Signed-off-by: Alejandro Cabrera Aldaya <aldaya@gmail.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
I don't know why but `echo -n` didn't work for me. macOS supports
the `-n` option but it doesn't work in the makefile. What it does
instead is it literally writes `-n` to the file and then also
leaves a newline at the end.
I'm using GNU Make 4.4 (`gmake` from Homebrew).
Signed-off-by: KaDiWa <kalle.wachsmuth@gmail.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Corrected the same parameter of writel_relaxed in sun20i_d1_riscv_cfg_init
to be u32 for a while and u64 for a while.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Split up sbi_ecall_replace so that each extension is in its individual
file.
Also reorganize the corresponding section in lib/sbi/objects.mk so
that it is grouped by extension, now that the object file targets are
split up.
Signed-off-by: Vivian Wang <dramforever@live.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
We fix the following semihosting compile error observed using LLVM:
lib/utils/serial/semihosting.c:158:12: error: result of comparison of constant -1 with expression of type 'char' is always true [-Werror,-Wtautological-constant-out-of-range-compare]
ret = ch > -1 ? ch : -1;
~~ ^ ~~
Fixes: 7f09fba86e ("lib: utils/serial: add semihosting support")
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
uart->reg_offset and uart->reg_io_width are only used on uart8250 and
not required on other platforms. Remove for sifive and gaisler.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
For each SBI extension, we:
- Add a Kconfig option for it
- Add the extension to sbi_ecall_exts only if the extension is enabled
- Add the corresponding sbi_ecall_* object file only if the extension is
enabled
Special cases are as follows:
- The legacy extensions are lumped together as one 'big' extension, as
has always been the case in OpenSBI code.
- The platform-defined vendor extensions are regarded as one extension.
- The Base extension cannot be disabled.
- sbi_ecall_replace implements multiple extensions, so it's not easy to
avoid linking it in. Enable it always, and use #ifdef to
disable/enable individual extensions.
Signed-off-by: Vivian Wang <dramforever@live.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Instead of hard-coding the list of extensions in C code, use carray to
generate the list of extensions.
Using carray makes adding and removing extensions slightly cleaner. This
also paves the way for using Kconfig to disable unneeded extensions.
Signed-off-by: Vivian Wang <dramforever@live.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Add back the missing rules needed to build carray files in lib/sbi. This
allows future usage of carray in lib/sbi.
Fixes: de80e9337d ("Makefile: Compile lib/utils sources separately for each platform")
Signed-off-by: Vivian Wang <dramforever@live.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Since
commit 9c07c513aa ("firmware:Remove FW_PAYLOAD_FDT_PATH compile-time option"),
the section where FDT would be embedded in has changed from *.text* to *.rodata*,
but some places in fw_payload.md and fw.md are still *.text*.
This patch updates the document.
Signed-off-by: Yangjie Zhang <pyjmstr@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Add cscope support so that running `make cscope` will generate/update
cscope files used for source code browsing, while running `make
distclean` will remove the cscope files.
Also add entry in .gitignore to ignore generated cscope files.
Signed-off-by: Tan En De <ende.tan@linux.starfivetech.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
We update ae350 documentation to add details about platform device tree.
The nodes and their properties must be provided to properly initialize
data of underlying hardware and access their mmio registers.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Add domains_init platform hook for Andes AE350, users can add domain
description in device tree and select FDT domain support in Kconfig
to achieve system-level partitioning.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Move Andes PLICSW ipi device to fdt ipi framework, this patch is based
on Leo's modified IPI scheme on PLICSW.
Current IPI scheme uses bit 0 of pending reigster on PLICSW to send IPI
from hart 0 to hart 7, but bit 0 needs to be hardwired to 0 according
to spec. After some investigation, self-IPI seems to be seldom or never
used, so we re-order the IPI scheme to support 8 core platforms.
dts example (Quad-core AX45MP):
plicsw: interrupt-controller@e6400000 {
compatible = "andestech,plicsw";
reg = <0x00000000 0xe6400000 0x00000000 0x00400000>;
interrupts-extended = <&CPU0_intc 3
&CPU1_intc 3
&CPU2_intc 3
&CPU3_intc 3>;
interrupt-controller;
#address-cells = <2>;
#interrupt-cells = <2>;
};
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
This patch adds fw_platform_init() to initialize ae350 platform.name
and platform.hart_count by parsing device tree.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Andes PLIC is compatible with plic driver. The PLIC base address and
number of source can be obtained by parsing the device tree.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The boot-time cache operations have been handled by U-boot SPL, so we
can drop duplicate code.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
This patch generalizes the logic to add a memory range with desired
alignment and flags of consecutive regions to the root domain.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
With the T-HEAD C9XX cores being designed before or during ratification
of the SSCOFPMF extension, they implement a PMU extension that behaves
very similar but not equal to it by providing overflow interrupts though
in a slightly different registers format.
The sun20i-d1 is using this core. So implement the necessary overrides
to allow its pmu to be used via the standard sbi-pmu extension.
For now it's also the only soc using this core, so keep the additional
code in the d1-space for now.
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Init of non-standard extensions is a platform-specific thing,
so allow generic platforms to do this via a platform-override.
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The platform-specific extension_init callback is supposed to
set specific things for the platform opensbi is running on.
So it's also the right place to override specific hart_features
if needed - when it's know that autodetection has provided
wrong results for example.
Suggested-by: Atish Patra <atishp@atishpatra.org>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Platforms may need to override auto-detected hart features
in their override functions. So move the hart_features
struct to the sbi_hart.h header allowing us to pass it over
to platform-handlers.
Suggested-by: Atish Patra <atishp@atishpatra.org>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Don't spread checking for pmu extensions through the code
but instead introduce a sbi-pmu function that other code can
call to get the correct information about the existence of the
pmu interrupt.
Add a sbi_pmu_device override function to allow overridung this
bit as well if needed.
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch does following fixes in fdt_pmu_setup():
1) If any of the event mapping DT property is absent or too small
then don't skip parsing of other DT properties.
2) Return failure if sbi_pmu_add_hw_event_counter_map() fails.
3) Return failure if sbi_pmu_add_raw_event_counter_map() fails.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
If a particular misaligned load or store cannot be emulated at all, for
the redirected trap, trap.gva is set to 0, but it should be the same as
mstatus[h].GVA of the original trap. Fix this so that if the trap is
destined for HS-mode, hstatus.GVA is then set correctly.
Fixes: 1c4ce74f51 ("lib: sbi: Set gva when creating sbi_trap_info")
Signed-off-by: Vivian Wang <dramforever@live.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The GVA bit is in mstatus on RV64, and in mstatush in RV32. Refactor
code handling this in sbi_trap_handler into a helper function to extract
GVA from sbi_trap_regs, so that future code accessing GVA can be
XLEN-agnostic.
Signed-off-by: Vivian Wang <dramforever@live.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Extend example for Unmatched board to provide SBI PMU bindings
for generalized and cache event's where they are applicable.
Signed-off-by: Nikita Shubin <n.shubin@yadro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
bitmap for MHPMCOUNTERx should be 0x18 and not 0x0c, we check
against SBI_PMU_FIXED_CTR_MASK which assumes than first 3 bits are
dedicated to mcycle, mtime and minstret, u74 has 2 hardware counters.
Reported-by: Zhang Xin <zhangxin.xa@gmail.com>
Signed-off-by: Nikita Shubin <n.shubin@yadro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The sbi_pmu.h should only include minimal required headers whereas
sbi_pmu.c should include all required headers.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Let us print the platform PMU device name at the boot-time so that users
know whether the underlying platform has custom per-HART PMU operations.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
We extend SBI PMU implementation to allow custom PMU device operations
which a platform can use for platform specific quirks.
The custom PMU device operations added by this patch include:
1) Operations to allow a platform implement custom firmware events.
These custom firmware events can be SBI vendor extension related
events or platform specific per-HART events are not possible to
count through HPM CSRs.
2) Operations to allow a platform implement custom way for enabling
(or disabling) an overflow interrupt (e.g. T-Head C9xx).
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Currently, we have 32 elements (i.e. SBI_PMU_FW_EVENT_MAX) array of
"struct sbi_pmu_fw_event" for each of 128 possible HARTs
(i.e. SBI_HARTMASK_MAX_BITS).
To reduce memory usage of OpenSBI, we update FW counter implementation
as follows:
1) Remove SBI_PMU_FW_EVENT_MAX
2) Remove "struct sbi_pmu_fw_event"
3) Create per-HART bitmap of XLEN bits to track FW counters
which are started on each HART
4) Create per-HART uint64_t array to track values of FW
counters on each HART.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
As-per SBI specification, all firmware counters are always 64 bits
wide so let us update the SBI PMU implementation to reflect this fact.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
The "read a firmware counter" SBI call should only work for firmware
counters so let us replace sbi_pmu_ctr_read() with sbi_pmu_ctr_fw_read()
which works only on firmware counters.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
sideleg and sedeleg csrs are not part of riscv isa spec
anymore, these csrs were part of N extension which
is removed from the riscv isa specification.
These commits removed all traces of these csrs from
riscv spec (https://github.com/riscv/riscv-isa-manual) -
commit f8d27f805b65 ("Remove or downgrade more references to N extension (#674)")
commit b6cade07034d ("Remove N extension chapter for now")
Signed-off-by: Rahul Pathak <rpathak@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
In case of missing "FENCE.TSO" instruction implementation,
opensbi can emulate the "FENCE.TSO" with "FENCE RW,RW", but
mepc was not incremented to continue from the next instruction
causing infinite trap.
Fixes: cb8271c8 ("lib: sbi_illegal_insn: Add emulation for fence.tso")
Signed-off-by: Rahul Pathak <rpathak@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
The privileged spec specifies that on a trap to HS-mode, hstatus.GVA
should be set to 1 if stval is written with a guest virtual address, and
to 0 otherwise. Implement this by setting hstatus.GVA to trap->gva when
redirecting traps to HS-mode.
Signed-off-by: Vivian Wang <dramforever@live.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The hypervisor CSRs hstatus, htval, htinst should always be set if the
trap is to be taken in HS-mode, regardless of which mode it came from.
Signed-off-by: Vivian Wang <dramforever@live.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
In some cases the sbi_trap_info argument passed to sbi_trap_redirect is
created from scratch by filling its fields. Since we previously added a
gva field to struct sbi_trap_info, initialize gva in these cases also.
Suggested-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Vivian Wang <dramforever@live.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The machine mode GVA field is available if the hypervisor extension is
implemented, and indicates if mtval is a guest virtual address. Add a
gva field to sbi_trap_info for this, and in __sbi_expected_trap_hext,
save mstatus[h].GVA to it, so that gva indicates if tval is a guest
virtual address. If the hypervisor extension is not implemented, always
set gva to 0.
Signed-off-by: Vivian Wang <dramforever@live.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The machine mode GVA field is in mstatus for RV64 and mstatush for RV32,
and is available if the hypervisor extension is available. If an
exception occurs, we may need to redirect the trap to HS-mode, in which
case, hstatus.GVA should be set to same as the machine mode GVA bit.
Add MSTATUS_GVA for RV64, MSTATUSH_GVA for RV32, and their SHIFT
encodings. The SHIFT index is helpful in assembly code, since field
extraction can be implemented in only one register. In pseudocode:
- For RV32: gva = (mstatus >> MSTATUS_GVA_SHIFT) & 1;
- For RV64: gva = (mstatush >> MSTATUSH_GVA_SHIFT) & 1;
Signed-off-by: Vivian Wang <dramforever@live.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
We update all documentation files to:
1) Remove references to platform specific config.mk file since it is
has been removed.
2) Add details about platform specific configs/defconfig and Kconfig
files mandatory for each platform.
3) Add required packages in top-level README.md
4) Fix typo releated to object.mk in docs/platform/platform.md
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Tested-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Atish Patra <atishp@rivosinc.com>
Tested-by: Atish Patra <atishp@rivosinc.com>
We update generic platform to use kconfig for enabling/disabling
platform overrides. We also enable all platform overrides in generic
platform defconfig.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Tested-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Atish Patra <atishp@rivosinc.com>
Tested-by: Atish Patra <atishp@rivosinc.com>
We update gpio drivers makefile to use kconfig for enabling/disabling
drivers. To avoid compile errors, we also enable appropriate gpio
drivers for each platform.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Tested-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Atish Patra <atishp@rivosinc.com>
Tested-by: Atish Patra <atishp@rivosinc.com>
We update i2c drivers makefile to use kconfig for enabling/disabling
drivers. To avoid compile errors, we also enable appropriate i2c
drivers for each platform.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Tested-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Atish Patra <atishp@rivosinc.com>
Tested-by: Atish Patra <atishp@rivosinc.com>
We update irqchip drivers makefile to use kconfig for enabling/disabling
drivers. To avoid compile errors, we also enable appropriate irqchip
drivers for each platform.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Tested-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Atish Patra <atishp@rivosinc.com>
Tested-by: Atish Patra <atishp@rivosinc.com>
We update ipi drivers makefile to use kconfig for enabling/disabling
drivers. To avoid compile errors, we also enable appropriate ipi
drivers for each platform.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Tested-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Atish Patra <atishp@rivosinc.com>
Tested-by: Atish Patra <atishp@rivosinc.com>
We update timer drivers makefile to use kconfig for enabling/disabling
drivers. To avoid compile errors, we also enable appropriate timer
drivers for each platform.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Tested-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Atish Patra <atishp@rivosinc.com>
Tested-by: Atish Patra <atishp@rivosinc.com>
We update system drivers makefile to use kconfig for enabling/disabling
drivers. To avoid compile errors, we also enable appropriate system
drivers for each platform.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Tested-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Atish Patra <atishp@rivosinc.com>
Tested-by: Atish Patra <atishp@rivosinc.com>
We update reset drivers makefile to use kconfig for enabling/disabling
drivers. To avoid compile errors, we also enable appropriate reset
drivers for each platform.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Tested-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Atish Patra <atishp@rivosinc.com>
Tested-by: Atish Patra <atishp@rivosinc.com>
We update serial drivers makefile to use kconfig for enabling/disabling
drivers. To avoid compile errors, we also enable appropriate serial
drivers for each platform.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Tested-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Atish Patra <atishp@rivosinc.com>
Tested-by: Atish Patra <atishp@rivosinc.com>
Currently, if same build directory is used to compile two different
platforms then lib/utils objects are shared for these platforms.
We will be having platform specific configs to enable/disable drivers
in lib/utils and select compile time options for lib/utils sources.
This means lib/utils sources will now be compiled in a platform
specific way.
To tackle above, we update top-level Makefile as follows:
1) Don't create libsbiutils.a anymore because this can't be shared
between platforms.
2) Compile lib/utils sources separately for each platform.
3) Add comments showing which make rules are for lib/sbi, lib/utils,
firmware, and platform sources.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Tested-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Atish Patra <atishp@rivosinc.com>
Tested-by: Atish Patra <atishp@rivosinc.com>
We extend the top-level makefile to allow kconfig based configuration
for each platform where each platform has it's own set of configs with
"defconfig" being the default config.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Tested-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Atish Patra <atishp@rivosinc.com>
Tested-by: Atish Patra <atishp@rivosinc.com>
We adopt Kconfiglib v14.1.0 sources under scripts directory so that
top-level OpenSBI makefile can directly use Kconfiglib scripts without
expecting users to install a particular version of Kconfiglib on their
build system.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Tested-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Atish Patra <atishp@rivosinc.com>
Tested-by: Atish Patra <atishp@rivosinc.com>
Read long long arguments directly using va_arg. Remove original hack for
RV32 that read a long long arg as two long args.
This un-breaks the case on RV64 where e.g. the long long is followed by
an odd number of ints:
sbi_printf("%d %lld", (int) 1, (long long) 2LL);
Also remove the acnt variable, which is now unused.
Signed-off-by: dramforever <dramforever@live.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
RISC-V doesn't generate exceptions on divide-by-zero, but the result,
all bits set, is not likely what people expect either. In all cases
where we divide by baudrate there's a chance it's zero (when the DT
it came from is "bad"). To avoid difficult to debug situations, leave
baudrate dependent registers alone when baudrate is zero, as, also in
all cases, it appears we can skip initialization of those registers
and still [hopefully] have a functioning UART.
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
While it doesn't look like there are any current cases of using
uninitialized data, let's zero all the UART data members to be
safe. Zero may not actually be better than a random number in
some cases, so all structure members should still be validated
before use, but at least zero is usually easier to debug than
some random stack garbage...
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Factor out the common code used by the fdt UART node parsers,
allowing us to drop duplicate code.
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
fw_event_map represents array of firmware events. It should initialized
for maximum number of firmware events not counters.
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The active_events array is accessed with counter ID passed from the supervisor
software before the counter ID bound check. This may cause a buffer overrun
if a supervisor passes an invalid counter ID.
Fix this by moving the access part after the bound check.
Reported-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Currently, there is no sanity check for firmware event code. We don't see
any issue as Linux kernel driver does a bound check on firmware events
already. However, OpenSBI can't assume sane supervisor mode software
always. Thus, an invalid event idx can cause a buffer overflow error.
For hardware events, the match will fail for invalid event code anyways.
However, a search is unecessary if event code is invalid.
Add a event ID validation function to solve the issue.
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The current implementation computes the possible counter range
by doing a left shift of counter base. However, this may overflow depending
on the counter base value. In case of overflow, the highest counter id
may be computed incorrectly. As per the SBI specification, the respective
function should return an error if any of the counter is not valid.
Fix the counter index check by avoiding left shifting while doing the
sanity checks. Without the shift, the implementation just iterates
over the counter mask and computes the correct counter index by adding
the base to it.
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
printc would happily write to 'out' even when 'out_len' was zero,
potentially overflowing buffers. Rework printc to not do that and
also ensure the null byte is written at the last position when
necessary, as stated in the snprintf man page. Also, panic if
sprintf or snprintf are called with NULL output strings (except
the special case of snprintf having a NULL output string and
a zero output size, allowing it to be used to get the number of
characters that would have been written). Finally, rename a
goto label which clashed with 'out'.
Fixes: 9e8ff05cb6 ("Initial commit.")
Signed-off-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The age old version of Shakti UART was upgraded long back, but we missed
updating the driver in OpenSBI. The old version of UART is not supported
anymore, hence removed the inline comment which is also outdated now.
Signed-off-by: Prasanna T <ptprasanna@gmail.com>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Xiang W <wxjstz@126.com>
MPV bit is set when the value of next_virt boolean variable equals
true. Since the value of next_virt is either 0 or 1, we can set
MPV bit without if-else logic.
Signed-off-by: Che-Chia Chang <alvinga@andestech.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
If the ecall SBI_EXT_HSM_HART_START is called it might try to wake the
secondary hart using sbi_ipi_raw_send() to send an IPI to the hart.
This can fail if there is no IPI device but no error is returned from
sbi_ipi_raw_send() so the ecall returns as if the action completed and
the caller continues without noticing (in the case of Linux it just hangs
waiting for the secondary hart to become active)
Fix this by changing sbi_ipi_raw_send() to return and error, and if an
error is returned, then return it via SBI_EXT_HSM_HART_START call.
Signed-off-by: Ben Dooks <ben.dooks@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Motivation: Suppose a peripheral needs to be configured to transmit
data. There is an SFR bit which indicates that the peripheral is ready
to transmit. The firmware should check the bit and will only transmit
data when the peripheral is ready. When the firmware starts polling the
SFR, the peripheral could be busy transmitting/receiving other data so
the firmware must wait till that completes. Assuming that there is no
other way, the firmware shouldn't wait indefinitely.
The function sbi_timer_waitms_until() will constantly check whether a
certain condition is satisfied, or timeout occurs. It can be used for
the cases when a timeout is required.
Signed-off-by: Adnan Rahman Chowdhury <adnan.chowdhury@sifive.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
2022-07-08 14:51:24 +05:30
308 changed files with 23123 additions and 4330 deletions
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
