tohost is not required in hifive1 env

bare-metal-bsp/drivers/fe300prci/fe300prci_driver.c

@@ -2,7 +2,7 @@
 
 #include "platform.h"
 
-#ifdef PRCI_BASE_ADDR
+#ifdef PRCI_CTRL_ADDR
 #include "fe300prci/fe300prci_driver.h"
 #include <unistd.h>
 

bare-metal-bsp/env/common-gcc.mk

@@ -55,7 +55,7 @@ OBJDUMP := $(TOOL_DIR)$(TRIPLET)-objdump
 
 
 $(TARGET): $(LINK_OBJS) $(LINK_DEPS)
-	$(LD) $(LINK_OBJS) $(LDFLAGS) $(LIBWRAP) -o $@
+	$(LD) $(LINK_OBJS) $(LDFLAGS) -o $@
 	$(OBJDUMP) -d -S $(TARGET) > $(TARGET).dis
 	
 $(ASM_OBJS): %.o: %.S $(HEADERS)

bare-metal-bsp/env/hifive1.h

@@ -0,0 +1,81 @@
+// See LICENSE for license details.
+
+#ifndef _SIFIVE_HIFIVE1_H
+#define _SIFIVE_HIFIVE1_H
+
+#include <stdint.h>
+
+/****************************************************************************
+ * GPIO Connections
+ *****************************************************************************/
+
+// These are the GPIO bit offsets for the RGB LED on HiFive1 Board.
+// These are also mapped to RGB LEDs on the Freedom E300 Arty
+// FPGA
+// Dev Kit.
+
+#define RED_LED_OFFSET   22
+#define GREEN_LED_OFFSET 19
+#define BLUE_LED_OFFSET  21
+
+// These are the GPIO bit offsets for the differen digital pins
+// on the headers for both the HiFive1 Board and the Freedom E300 Arty FPGA Dev Kit.
+#define PIN_0_OFFSET 16
+#define PIN_1_OFFSET 17
+#define PIN_2_OFFSET 18
+#define PIN_3_OFFSET 19
+#define PIN_4_OFFSET 20
+#define PIN_5_OFFSET 21
+#define PIN_6_OFFSET 22
+#define PIN_7_OFFSET 23
+#define PIN_8_OFFSET 0
+#define PIN_9_OFFSET 1
+#define PIN_10_OFFSET 2
+#define PIN_11_OFFSET 3
+#define PIN_12_OFFSET 4
+#define PIN_13_OFFSET 5
+//#define PIN_14_OFFSET 8 //This pin is not connected on either board.
+#define PIN_15_OFFSET 9
+#define PIN_16_OFFSET 10
+#define PIN_17_OFFSET 11
+#define PIN_18_OFFSET 12
+#define PIN_19_OFFSET 13
+
+// These are *PIN* numbers, not
+// GPIO Offset Numbers.
+#define PIN_SPI1_SCK    (13u)
+#define PIN_SPI1_MISO   (12u)
+#define PIN_SPI1_MOSI   (11u)
+#define PIN_SPI1_SS0    (10u)
+#define PIN_SPI1_SS1    (14u) 
+#define PIN_SPI1_SS2    (15u)
+#define PIN_SPI1_SS3    (16u)
+
+#define SS_PIN_TO_CS_ID(x) \
+  ((x==PIN_SPI1_SS0 ? 0 :		 \
+    (x==PIN_SPI1_SS1 ? 1 :		 \
+     (x==PIN_SPI1_SS2 ? 2 :		 \
+      (x==PIN_SPI1_SS3 ? 3 :		 \
+       -1))))) 
+
+
+// These buttons are present only on the Freedom E300 Arty Dev Kit.
+#ifdef HAS_BOARD_BUTTONS
+#define BUTTON_0_OFFSET 15
+#define BUTTON_1_OFFSET 30
+#define BUTTON_2_OFFSET 31
+
+#define INT_DEVICE_BUTTON_0 (INT_GPIO_BASE + BUTTON_0_OFFSET)
+#define INT_DEVICE_BUTTON_1 (INT_GPIO_BASE + BUTTON_1_OFFSET)
+#define INT_DEVICE_BUTTON_2 (INT_GPIO_BASE + BUTTON_2_OFFSET)
+
+#endif
+
+#define HAS_HFXOSC 1
+#define HAS_LFROSC_BYPASS 1
+
+#define RTC_FREQ 32768
+
+void write_hex(int fd, unsigned long int hex);
+
+#endif /* _SIFIVE_HIFIVE1_H */

bare-metal-bsp/env/hifive1/dhrystone.lds

@@ -0,0 +1,157 @@
+OUTPUT_ARCH( "riscv" )
+
+ENTRY( _start )
+
+MEMORY
+{
+  flash (rxai!w) : ORIGIN = 0x20400000, LENGTH = 512M
+  ram (wxa!ri) : ORIGIN = 0x80000000, LENGTH = 16K
+}
+
+PHDRS
+{
+  flash PT_LOAD;
+  ram_init PT_LOAD;
+  ram PT_NULL;
+}
+
+SECTIONS
+{
+  __stack_size = DEFINED(__stack_size) ? __stack_size : 2K;
+
+  .init           :
+  {
+    KEEP (*(SORT_NONE(.init)))
+  } >flash AT>flash :flash
+
+  .text           :
+  {
+    *(.text.unlikely .text.unlikely.*)
+    *(.text.startup .text.startup.*)
+    *(.text .text.*)
+    *(.gnu.linkonce.t.*)
+  } >flash AT>flash :flash
+
+  .fini           :
+  {
+    KEEP (*(SORT_NONE(.fini)))
+  } >flash AT>flash :flash
+
+  PROVIDE (__etext = .);
+  PROVIDE (_etext = .);
+  PROVIDE (etext = .);
+
+  . = ALIGN(4);
+
+  .preinit_array  :
+  {
+    PROVIDE_HIDDEN (__preinit_array_start = .);
+    KEEP (*(.preinit_array))
+    PROVIDE_HIDDEN (__preinit_array_end = .);
+  } >flash AT>flash :flash
+
+  .init_array     :
+  {
+    PROVIDE_HIDDEN (__init_array_start = .);
+    KEEP (*(SORT_BY_INIT_PRIORITY(.init_array.*) SORT_BY_INIT_PRIORITY(.ctors.*)))
+    KEEP (*(.init_array EXCLUDE_FILE (*crtbegin.o *crtbegin?.o *crtend.o *crtend?.o ) .ctors))
+    PROVIDE_HIDDEN (__init_array_end = .);
+  } >flash AT>flash :flash
+
+  .fini_array     :
+  {
+    PROVIDE_HIDDEN (__fini_array_start = .);
+    KEEP (*(SORT_BY_INIT_PRIORITY(.fini_array.*) SORT_BY_INIT_PRIORITY(.dtors.*)))
+    KEEP (*(.fini_array EXCLUDE_FILE (*crtbegin.o *crtbegin?.o *crtend.o *crtend?.o ) .dtors))
+    PROVIDE_HIDDEN (__fini_array_end = .);
+  } >flash AT>flash :flash
+
+  .ctors          :
+  {
+    /* gcc uses crtbegin.o to find the start of
+       the constructors, so we make sure it is
+       first.  Because this is a wildcard, it
+       doesn't matter if the user does not
+       actually link against crtbegin.o; the
+       linker won't look for a file to match a
+       wildcard.  The wildcard also means that it
+       doesn't matter which directory crtbegin.o
+       is in.  */
+    KEEP (*crtbegin.o(.ctors))
+    KEEP (*crtbegin?.o(.ctors))
+    /* We don't want to include the .ctor section from
+       the crtend.o file until after the sorted ctors.
+       The .ctor section from the crtend file contains the
+       end of ctors marker and it must be last */
+    KEEP (*(EXCLUDE_FILE (*crtend.o *crtend?.o ) .ctors))
+    KEEP (*(SORT(.ctors.*)))
+    KEEP (*(.ctors))
+  } >flash AT>flash :flash
+
+  .dtors          :
+  {
+    KEEP (*crtbegin.o(.dtors))
+    KEEP (*crtbegin?.o(.dtors))
+    KEEP (*(EXCLUDE_FILE (*crtend.o *crtend?.o ) .dtors))
+    KEEP (*(SORT(.dtors.*)))
+    KEEP (*(.dtors))
+  } >flash AT>flash :flash
+
+  .lalign         :
+  {
+    . = ALIGN(4);
+    PROVIDE( _data_lma = . );
+  } >flash AT>flash :flash
+
+  .dalign         :
+  {
+    . = ALIGN(4);
+    PROVIDE( _data = . );
+  } >ram AT>flash :ram_init
+
+  .data          :
+  {
+    *(.rdata)
+    *(.rodata .rodata.*)
+    *(.gnu.linkonce.r.*)
+    *(.data .data.*)
+    *(.gnu.linkonce.d.*)
+    . = ALIGN(8);
+    PROVIDE( __global_pointer$ = . + 0x800 );
+    *(.sdata .sdata.*)
+    *(.gnu.linkonce.s.*)
+    . = ALIGN(8);
+    *(.srodata.cst16)
+    *(.srodata.cst8)
+    *(.srodata.cst4)
+    *(.srodata.cst2)
+    *(.srodata .srodata.*)
+  } >ram AT>flash :ram_init
+
+  . = ALIGN(4);
+  PROVIDE( _edata = . );
+  PROVIDE( edata = . );
+
+  PROVIDE( _fbss = . );
+  PROVIDE( __bss_start = . );
+  .bss            :
+  {
+    *(.sbss*)
+    *(.gnu.linkonce.sb.*)
+    *(.bss .bss.*)
+    *(.gnu.linkonce.b.*)
+    *(COMMON)
+    . = ALIGN(4);
+  } >ram AT>ram :ram
+
+  . = ALIGN(8);
+  PROVIDE( _end = . );
+  PROVIDE( end = . );
+
+  .stack ORIGIN(ram) + LENGTH(ram) - __stack_size :
+  {
+    PROVIDE( _heap_end = . );
+    . = __stack_size;
+    PROVIDE( _sp = . );
+  } >ram AT>ram :ram
+}

bare-metal-bsp/env/hifive1/init.c

@@ -0,0 +1,238 @@
+#include <stdint.h>
+#include <stdio.h>
+#include <unistd.h>
+
+#include "../hifive1/platform.h"
+#include "encoding.h"
+
+extern int main(int argc, char** argv);
+extern void trap_entry();
+
+static unsigned long mtime_lo(void)
+{
+  return *(volatile unsigned long *)(CLINT_CTRL_ADDR + CLINT_MTIME);
+}
+
+#ifdef __riscv32
+
+static uint32_t mtime_hi(void)
+{
+  return *(volatile uint32_t *)(CLINT_CTRL_ADDR + CLINT_MTIME + 4);
+}
+
+uint64_t get_timer_value()
+{
+  while (1) {
+    uint32_t hi = mtime_hi();
+    uint32_t lo = mtime_lo();
+    if (hi == mtime_hi())
+      return ((uint64_t)hi << 32) | lo;
+  }
+}
+
+#else /* __riscv32 */
+
+uint64_t get_timer_value()
+{
+  return mtime_lo();
+}
+
+#endif
+
+unsigned long get_timer_freq()
+{
+  return 32768;
+}
+
+static void use_hfrosc(int div, int trim)
+{
+  // Make sure the HFROSC is running at its default setting
+  PRCI_REG(PRCI_HFROSCCFG) = (ROSC_DIV(div) | ROSC_TRIM(trim) | ROSC_EN(1));
+  while ((PRCI_REG(PRCI_HFROSCCFG) & ROSC_RDY(1)) == 0) ;
+  PRCI_REG(PRCI_PLLCFG) &= ~PLL_SEL(1);
+}
+
+static void use_pll(int refsel, int bypass, int r, int f, int q)
+{
+  // Ensure that we aren't running off the PLL before we mess with it.
+  if (PRCI_REG(PRCI_PLLCFG) & PLL_SEL(1)) {
+    // Make sure the HFROSC is running at its default setting
+    use_hfrosc(4, 16);
+  }
+
+  // Set PLL Source to be HFXOSC if available.
+  uint32_t config_value = 0;
+
+  config_value |= PLL_REFSEL(refsel);
+
+  if (bypass) {
+    // Bypass
+    config_value |= PLL_BYPASS(1);
+
+    PRCI_REG(PRCI_PLLCFG) = config_value;
+
+    // If we don't have an HFXTAL, this doesn't really matter.
+    // Set our Final output divide to divide-by-1:
+    PRCI_REG(PRCI_PLLDIV) = (PLL_FINAL_DIV_BY_1(1) | PLL_FINAL_DIV(0));
+  } else {
+    // In case we are executing from QSPI,
+    // (which is quite likely) we need to
+    // set the QSPI clock divider appropriately
+    // before boosting the clock frequency.
+
+    // Div = f_sck/2
+    SPI0_REG(SPI_REG_SCKDIV) = 8;
+
+    // Set DIV Settings for PLL
+    // Both HFROSC and HFXOSC are modeled as ideal
+    // 16MHz sources (assuming dividers are set properly for
+    // HFROSC).
+    // (Legal values of f_REF are 6-48MHz)
+
+    // Set DIVR to divide-by-2 to get 8MHz frequency
+    // (legal values of f_R are 6-12 MHz)
+
+    config_value |= PLL_BYPASS(1);
+    config_value |= PLL_R(r);
+
+    // Set DIVF to get 512Mhz frequncy
+    // There is an implied multiply-by-2, 16Mhz.
+    // So need to write 32-1
+    // (legal values of f_F are 384-768 MHz)
+    config_value |= PLL_F(f);
+
+    // Set DIVQ to divide-by-2 to get 256 MHz frequency
+    // (legal values of f_Q are 50-400Mhz)
+    config_value |= PLL_Q(q);
+
+    // Set our Final output divide to divide-by-1:
+    PRCI_REG(PRCI_PLLDIV) = (PLL_FINAL_DIV_BY_1(1) | PLL_FINAL_DIV(0));
+
+    PRCI_REG(PRCI_PLLCFG) = config_value;
+
+    // Un-Bypass the PLL.
+    PRCI_REG(PRCI_PLLCFG) &= ~PLL_BYPASS(1);
+
+    // Wait for PLL Lock
+    // Note that the Lock signal can be glitchy.
+    // Need to wait 100 us
+    // RTC is running at 32kHz.
+    // So wait 4 ticks of RTC.
+    uint32_t now = mtime_lo();
+    while (mtime_lo() - now < 4) ;
+
+    // Now it is safe to check for PLL Lock
+    while ((PRCI_REG(PRCI_PLLCFG) & PLL_LOCK(1)) == 0) ;
+  }
+
+  // Switch over to PLL Clock source
+  PRCI_REG(PRCI_PLLCFG) |= PLL_SEL(1);
+}
+
+static void use_default_clocks()
+{
+  // Turn off the LFROSC
+  AON_REG(AON_LFROSC) &= ~ROSC_EN(1);
+
+  // Use HFROSC
+  use_hfrosc(4, 16);
+}
+
+static unsigned long __attribute__((noinline)) measure_cpu_freq(size_t n)
+{
+  unsigned long start_mtime, delta_mtime;
+  unsigned long mtime_freq = get_timer_freq();
+
+  // Don't start measuruing until we see an mtime tick
+  unsigned long tmp = mtime_lo();
+  do {
+    start_mtime = mtime_lo();
+  } while (start_mtime == tmp);
+
+  unsigned long start_mcycle = read_csr(mcycle);
+
+  do {
+    delta_mtime = mtime_lo() - start_mtime;
+  } while (delta_mtime < n);
+
+  unsigned long delta_mcycle = read_csr(mcycle) - start_mcycle;
+
+  return (delta_mcycle / delta_mtime) * mtime_freq
+         + ((delta_mcycle % delta_mtime) * mtime_freq) / delta_mtime;
+}
+
+unsigned long get_cpu_freq()
+{
+  static uint32_t cpu_freq;
+
+  if (!cpu_freq) {
+    // warm up I$
+    measure_cpu_freq(1);
+    // measure for real
+    cpu_freq = measure_cpu_freq(10);
+  }
+
+  return cpu_freq;
+}
+
+static void uart_init(size_t baud_rate)
+{
+  GPIO_REG(GPIO_IOF_SEL) &= ~IOF0_UART0_MASK;
+  GPIO_REG(GPIO_IOF_EN) |= IOF0_UART0_MASK;
+  UART0_REG(UART_REG_DIV) = get_cpu_freq() / baud_rate - 1;
+  UART0_REG(UART_REG_TXCTRL) |= UART_TXEN;
+}
+
+
+
+#ifdef USE_PLIC
+extern void handle_m_ext_interrupt();
+#endif
+
+#ifdef USE_M_TIME
+extern void handle_m_time_interrupt();
+#endif
+
+uintptr_t handle_trap(uintptr_t mcause, uintptr_t epc)
+{
+  if (0){
+#ifdef USE_PLIC
+    // External Machine-Level interrupt from PLIC
+  } else if ((mcause & MCAUSE_INT) && ((mcause & MCAUSE_CAUSE) == IRQ_M_EXT)) {
+    handle_m_ext_interrupt();
+#endif
+#ifdef USE_M_TIME
+    // External Machine-Level interrupt from PLIC
+  } else if ((mcause & MCAUSE_INT) && ((mcause & MCAUSE_CAUSE) == IRQ_M_TIMER)){
+    handle_m_time_interrupt();
+#endif
+  }
+  else {
+    write(1, "trap\n", 5);
+    _exit(1 + mcause);
+  }
+  return epc;
+}
+
+void _init()
+{
+  
+  #ifndef NO_INIT
+  use_default_clocks();
+  use_pll(0, 0, 1, 31, 1);
+  uart_init(115200);
+
+  printf("core freq at %d Hz\n", get_cpu_freq());
+
+  write_csr(mtvec, &trap_entry);
+  if (read_csr(misa) & (1 << ('F' - 'A'))) { // if F extension is present
+    write_csr(mstatus, MSTATUS_FS); // allow FPU instructions without trapping
+    write_csr(fcsr, 0); // initialize rounding mode, undefined at reset
+  }
+  #endif
+  
+}
+
+void _fini()
+{
+}

bare-metal-bsp/env/hifive1/link.lds

@@ -0,0 +1,169 @@
+OUTPUT_ARCH( "riscv" )
+
+ENTRY( _start )
+
+MEMORY
+{
+  flash (rxai!w) : ORIGIN = 0x20400000, LENGTH = 512M
+  ram (wxa!ri) : ORIGIN = 0x80000000, LENGTH = 1M
+}
+
+PHDRS
+{
+  flash PT_LOAD;
+  ram_init PT_LOAD;
+  ram PT_NULL;
+}
+
+SECTIONS
+{
+  __stack_size = DEFINED(__stack_size) ? __stack_size : 2K;
+
+  .init           :
+  {
+    KEEP (*(SORT_NONE(.init)))
+  } >flash AT>flash :flash
+
+  .text           :
+  {
+    *(.text.unlikely .text.unlikely.*)
+    *(.text.startup .text.startup.*)
+    *(.text .text.*)
+    *(.gnu.linkonce.t.*)
+  } >flash AT>flash :flash
+
+  .fini           :
+  {
+    KEEP (*(SORT_NONE(.fini)))
+  } >flash AT>flash :flash
+
+  PROVIDE (__etext = .);
+  PROVIDE (_etext = .);
+  PROVIDE (etext = .);
+
+  .rodata         :
+  {
+    *(.rdata)
+    *(.rodata .rodata.*)
+    *(.gnu.linkonce.r.*)
+  } >flash AT>flash :flash
+
+  . = ALIGN(4);
+
+  .preinit_array  :
+  {
+    PROVIDE_HIDDEN (__preinit_array_start = .);
+    KEEP (*(.preinit_array))
+    PROVIDE_HIDDEN (__preinit_array_end = .);
+  } >flash AT>flash :flash
+
+  .init_array     :
+  {
+    PROVIDE_HIDDEN (__init_array_start = .);
+    KEEP (*(SORT_BY_INIT_PRIORITY(.init_array.*) SORT_BY_INIT_PRIORITY(.ctors.*)))
+    KEEP (*(.init_array EXCLUDE_FILE (*crtbegin.o *crtbegin?.o *crtend.o *crtend?.o ) .ctors))
+    PROVIDE_HIDDEN (__init_array_end = .);
+  } >flash AT>flash :flash
+
+  .fini_array     :
+  {
+    PROVIDE_HIDDEN (__fini_array_start = .);
+    KEEP (*(SORT_BY_INIT_PRIORITY(.fini_array.*) SORT_BY_INIT_PRIORITY(.dtors.*)))
+    KEEP (*(.fini_array EXCLUDE_FILE (*crtbegin.o *crtbegin?.o *crtend.o *crtend?.o ) .dtors))
+    PROVIDE_HIDDEN (__fini_array_end = .);
+  } >flash AT>flash :flash
+
+  .ctors          :
+  {
+    /* gcc uses crtbegin.o to find the start of
+       the constructors, so we make sure it is
+       first.  Because this is a wildcard, it
+       doesn't matter if the user does not
+       actually link against crtbegin.o; the
+       linker won't look for a file to match a
+       wildcard.  The wildcard also means that it
+       doesn't matter which directory crtbegin.o
+       is in.  */
+    KEEP (*crtbegin.o(.ctors))
+    KEEP (*crtbegin?.o(.ctors))
+    /* We don't want to include the .ctor section from
+       the crtend.o file until after the sorted ctors.
+       The .ctor section from the crtend file contains the
+       end of ctors marker and it must be last */
+    KEEP (*(EXCLUDE_FILE (*crtend.o *crtend?.o ) .ctors))
+    KEEP (*(SORT(.ctors.*)))
+    KEEP (*(.ctors))
+  } >flash AT>flash :flash
+
+  .dtors          :
+  {
+    KEEP (*crtbegin.o(.dtors))
+    KEEP (*crtbegin?.o(.dtors))
+    KEEP (*(EXCLUDE_FILE (*crtend.o *crtend?.o ) .dtors))
+    KEEP (*(SORT(.dtors.*)))
+    KEEP (*(.dtors))
+  } >flash AT>flash :flash
+
+  .except :
+  {
+  	*(.gcc_except_table.*)
+  } >flash AT>flash :flash
+  
+  .lalign         :
+  {
+    . = ALIGN(4);
+    PROVIDE( _data_lma = . );
+  } >flash AT>flash :flash
+
+  .dalign         :
+  {
+    . = ALIGN(4);
+    PROVIDE( _data = . );
+  } >ram AT>flash :ram_init
+
+  .data          :
+  {
+    *(.data .data.*)
+    *(.gnu.linkonce.d.*)
+    . = ALIGN(8);
+    PROVIDE( __global_pointer$ = . + 0x800 );
+    *(.sdata .sdata.*)
+    *(.gnu.linkonce.s.*)
+    . = ALIGN(8);
+    *(.srodata.cst16)
+    *(.srodata.cst8)
+    *(.srodata.cst4)
+    *(.srodata.cst2)
+    *(.srodata .srodata.*)
+  } >ram AT>flash :ram_init
+
+  . = ALIGN(4);
+  PROVIDE( _edata = . );
+  PROVIDE( edata = . );
+
+  PROVIDE( _fbss = . );
+  PROVIDE( __bss_start = . );
+  .bss            :
+  {
+    *(.sbss*)
+    *(.gnu.linkonce.sb.*)
+    *(.bss .bss.*)
+    *(.gnu.linkonce.b.*)
+    *(COMMON)
+    . = ALIGN(4);
+  } >ram AT>ram :ram
+
+  . = ALIGN(8);
+  PROVIDE( _end = . );
+  PROVIDE( end = . );
+
+  .stack ORIGIN(ram) + LENGTH(ram) - __stack_size :
+  {
+    PROVIDE( _heap_end = . );
+    . = __stack_size;
+    PROVIDE( _sp = . );
+  } >ram AT>ram :ram
+
+  PROVIDE( tohost = 0xfffffff0 );
+  PROVIDE( fromhost = 0xfffffff8 );
+}

bare-metal-bsp/env/hifive1/openocd.cfg

@@ -0,0 +1,34 @@
+adapter_khz     10000
+
+interface ftdi
+ftdi_device_desc "Dual RS232-HS"
+ftdi_vid_pid 0x0403 0x6010
+
+ftdi_layout_init 0x0008 0x001b
+ftdi_layout_signal nSRST -oe 0x0020 -data 0x0020
+
+#Reset Stretcher logic on FE310 is ~1 second long
+#This doesn't apply if you use
+# ftdi_set_signal, but still good to document
+#adapter_nsrst_delay 1500
+
+set _CHIPNAME riscv
+jtag newtap $_CHIPNAME cpu -irlen 5 -expected-id 0x10e31913
+
+set _TARGETNAME $_CHIPNAME.cpu
+target create $_TARGETNAME riscv -chain-position $_TARGETNAME
+$_TARGETNAME configure -work-area-phys 0x80000000 -work-area-size 10000 -work-area-backup 1
+
+flash bank onboard_spi_flash fespi 0x20000000 0 0 0 $_TARGETNAME
+init
+#reset -- This type of reset is not implemented yet
+if {[ info exists pulse_srst]} {
+  ftdi_set_signal nSRST 0
+  ftdi_set_signal nSRST z
+  #Wait for the reset stretcher
+  #It will work without this, but
+  #will incur lots of delays for later commands.
+  sleep 1500
+}	
+halt
+#flash protect 0 64 last off

bare-metal-bsp/env/hifive1/platform.h

@@ -0,0 +1,133 @@
+// See LICENSE for license details.
+
+#ifndef _SIFIVE_PLATFORM_H
+#define _SIFIVE_PLATFORM_H
+
+// Some things missing from the official encoding.h
+#define MCAUSE_INT         0x80000000
+#define MCAUSE_CAUSE       0x7FFFFFFF
+
+#include "sifive/const.h"
+#include "sifive/devices/aon.h"
+#include "sifive/devices/clint.h"
+#include "sifive/devices/gpio.h"
+#include "sifive/devices/otp.h"
+#include "sifive/devices/plic.h"
+#include "sifive/devices/prci.h"
+#include "sifive/devices/pwm.h"
+#include "sifive/devices/spi.h"
+#include "sifive/devices/uart.h"
+
+/****************************************************************************
+ * Platform definitions
+ *****************************************************************************/
+
+// Memory map
+#define MASKROM_MEM_ADDR _AC(0x00001000,UL)
+#define TRAPVEC_TABLE_CTRL_ADDR _AC(0x00001010,UL)
+#define OTP_MEM_ADDR _AC(0x00020000,UL)
+#define CLINT_CTRL_ADDR _AC(0x02000000,UL)
+#define PLIC_CTRL_ADDR _AC(0x0C000000,UL)
+#define AON_CTRL_ADDR _AC(0x10000000,UL)
+#define PRCI_CTRL_ADDR _AC(0x10008000,UL)
+#define OTP_CTRL_ADDR _AC(0x10010000,UL)
+#define GPIO_CTRL_ADDR _AC(0x10012000,UL)
+#define UART0_CTRL_ADDR _AC(0x10013000,UL)
+#define SPI0_CTRL_ADDR _AC(0x10014000,UL)
+#define PWM0_CTRL_ADDR _AC(0x10015000,UL)
+#define UART1_CTRL_ADDR _AC(0x10023000,UL)
+#define SPI1_CTRL_ADDR _AC(0x10024000,UL)
+#define PWM1_CTRL_ADDR _AC(0x10025000,UL)
+#define SPI2_CTRL_ADDR _AC(0x10034000,UL)
+#define PWM2_CTRL_ADDR _AC(0x10035000,UL)
+#define SPI0_MEM_ADDR _AC(0x20000000,UL)
+#define MEM_CTRL_ADDR _AC(0x80000000,UL)
+
+// IOF masks
+#define IOF0_SPI1_MASK          _AC(0x000007FC,UL)
+#define SPI11_NUM_SS     (4)
+#define IOF_SPI1_SS0          (2u)
+#define IOF_SPI1_SS1          (8u)
+#define IOF_SPI1_SS2          (9u)
+#define IOF_SPI1_SS3          (10u)
+#define IOF_SPI1_MOSI         (3u)
+#define IOF_SPI1_MISO         (4u)
+#define IOF_SPI1_SCK          (5u)
+#define IOF_SPI1_DQ0          (3u)
+#define IOF_SPI1_DQ1          (4u)
+#define IOF_SPI1_DQ2          (6u)
+#define IOF_SPI1_DQ3          (7u)
+
+#define IOF0_SPI2_MASK          _AC(0xFC000000,UL)
+#define SPI2_NUM_SS       (1)
+#define IOF_SPI2_SS0          (26u)
+#define IOF_SPI2_MOSI         (27u)
+#define IOF_SPI2_MISO         (28u)
+#define IOF_SPI2_SCK          (29u)
+#define IOF_SPI2_DQ0          (27u)
+#define IOF_SPI2_DQ1          (28u)
+#define IOF_SPI2_DQ2          (30u)
+#define IOF_SPI2_DQ3          (31u)
+
+//#define IOF0_I2C_MASK          _AC(0x00003000,UL)
+
+#define IOF0_UART0_MASK         _AC(0x00030000, UL)
+#define IOF_UART0_RX   (16u)
+#define IOF_UART0_TX   (17u)
+
+#define IOF0_UART1_MASK         _AC(0x03000000, UL)
+#define IOF_UART1_RX (24u)
+#define IOF_UART1_TX (25u)
+
+#define IOF1_PWM0_MASK          _AC(0x0000000F, UL)
+#define IOF1_PWM1_MASK          _AC(0x00780000, UL)
+#define IOF1_PWM2_MASK          _AC(0x00003C00, UL)
+
+// Interrupt numbers
+#define INT_RESERVED 0
+#define INT_WDOGCMP 1
+#define INT_RTCCMP 2
+#define INT_UART0_BASE 3
+#define INT_UART1_BASE 4
+#define INT_SPI0_BASE 5
+#define INT_SPI1_BASE 6
+#define INT_SPI2_BASE 7
+#define INT_GPIO_BASE 8
+#define INT_PWM0_BASE 40
+#define INT_PWM1_BASE 44
+#define INT_PWM2_BASE 48
+
+// Helper functions
+#define _REG32(p, i) (*(volatile uint32_t *) ((p) + (i)))
+#define _REG32P(p, i) ((volatile uint32_t *) ((p) + (i)))
+#define AON_REG(offset) _REG32(AON_CTRL_ADDR, offset)
+#define CLINT_REG(offset) _REG32(CLINT_CTRL_ADDR, offset)
+#define GPIO_REG(offset) _REG32(GPIO_CTRL_ADDR, offset)
+#define OTP_REG(offset)  _REG32(OTP_CTRL_ADDR, offset)
+#define PLIC_REG(offset) _REG32(PLIC_CTRL_ADDR, offset)
+#define PRCI_REG(offset) _REG32(PRCI_CTRL_ADDR, offset)
+#define PWM0_REG(offset) _REG32(PWM0_CTRL_ADDR, offset)
+#define PWM1_REG(offset) _REG32(PWM1_CTRL_ADDR, offset)
+#define PWM2_REG(offset) _REG32(PWM2_CTRL_ADDR, offset)
+#define SPI0_REG(offset) _REG32(SPI0_CTRL_ADDR, offset)
+#define SPI1_REG(offset) _REG32(SPI1_CTRL_ADDR, offset)
+#define SPI2_REG(offset) _REG32(SPI2_CTRL_ADDR, offset)
+#define UART0_REG(offset) _REG32(UART0_CTRL_ADDR, offset)
+#define UART1_REG(offset) _REG32(UART1_CTRL_ADDR, offset)
+
+// Misc
+
+#include <stdint.h>
+
+#define NUM_GPIO 32
+
+#define PLIC_NUM_INTERRUPTS 52
+#define PLIC_NUM_PRIORITIES 7
+
+#include "hifive1.h"
+
+unsigned long get_cpu_freq(void);
+unsigned long get_timer_freq(void);
+uint64_t get_timer_value(void);
+
+#endif /* _SIFIVE_PLATFORM_H */

bare-metal-bsp/env/hifive1/settings.mk

@@ -0,0 +1,3 @@
+# Describes the CPU on this board to the rest of the SDK.
+RISCV_ARCH := rv32imac
+RISCV_ABI  := ilp32

bare-metal-bsp/env/iss/platform.h

@@ -6,6 +6,7 @@
 // Some things missing from the official encoding.h
 #define MCAUSE_INT         0x80000000
 #define MCAUSE_CAUSE       0x7FFFFFFF
+#define USE_TOHOST 1
 
 #include "rtl/const.h"
 /****************************************************************************

bare-metal-bsp/include/bsp.h

@@ -0,0 +1,22 @@
+/*
+ * bsp.h
+ *
+ *  Created on: 30.07.2018
+ *      Author: eyck
+ */
+
+#ifndef BSP_H_
+#define BSP_H_
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+#include <fe300prci/fe300prci_driver.h>
+#include <platform.h>
+#include <encoding.h>
+extern void trap_entry();
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* BSP_H_ */

bare-metal-bsp/include/sifive/bits.h

@@ -0,0 +1,36 @@
+// See LICENSE for license details.
+#ifndef _RISCV_BITS_H
+#define _RISCV_BITS_H
+
+#define likely(x) __builtin_expect((x), 1)
+#define unlikely(x) __builtin_expect((x), 0)
+
+#define ROUNDUP(a, b) ((((a)-1)/(b)+1)*(b))
+#define ROUNDDOWN(a, b) ((a)/(b)*(b))
+
+#define MAX(a, b) ((a) > (b) ? (a) : (b))
+#define MIN(a, b) ((a) < (b) ? (a) : (b))
+#define CLAMP(a, lo, hi) MIN(MAX(a, lo), hi)
+
+#define EXTRACT_FIELD(val, which) (((val) & (which)) / ((which) & ~((which)-1)))
+#define INSERT_FIELD(val, which, fieldval) (((val) & ~(which)) | ((fieldval) * ((which) & ~((which)-1))))
+
+#define STR(x) XSTR(x)
+#define XSTR(x) #x
+
+#if __riscv_xlen == 64
+# define SLL32    sllw
+# define STORE    sd
+# define LOAD     ld
+# define LWU      lwu
+# define LOG_REGBYTES 3
+#else
+# define SLL32    sll
+# define STORE    sw
+# define LOAD     lw
+# define LWU      lw
+# define LOG_REGBYTES 2
+#endif
+#define REGBYTES (1 << LOG_REGBYTES)
+
+#endif

bare-metal-bsp/include/sifive/const.h

@@ -0,0 +1,18 @@
+// See LICENSE for license details.
+/* Derived from <linux/const.h> */
+
+#ifndef _SIFIVE_CONST_H
+#define _SIFIVE_CONST_H
+
+#ifdef __ASSEMBLER__
+#define _AC(X,Y)        X
+#define _AT(T,X)        X
+#else
+#define _AC(X,Y)        (X##Y)
+#define _AT(T,X)        ((T)(X))
+#endif /* !__ASSEMBLER__*/
+
+#define _BITUL(x)       (_AC(1,UL) << (x))
+#define _BITULL(x)      (_AC(1,ULL) << (x))
+
+#endif /* _SIFIVE_CONST_H */

bare-metal-bsp/include/sifive/devices/aon.h

@@ -0,0 +1,88 @@
+// See LICENSE for license details.
+
+#ifndef _SIFIVE_AON_H
+#define _SIFIVE_AON_H
+
+/* Register offsets */
+
+#define AON_WDOGCFG     0x000
+#define AON_WDOGCOUNT   0x008
+#define AON_WDOGS       0x010
+#define AON_WDOGFEED    0x018
+#define AON_WDOGKEY     0x01C
+#define AON_WDOGCMP     0x020
+
+#define AON_RTCCFG      0x040
+#define AON_RTCLO       0x048
+#define AON_RTCHI       0x04C
+#define AON_RTCS        0x050
+#define AON_RTCCMP      0x060
+
+#define AON_BACKUP0     0x080
+#define AON_BACKUP1     0x084
+#define AON_BACKUP2     0x088
+#define AON_BACKUP3     0x08C
+#define AON_BACKUP4     0x090
+#define AON_BACKUP5     0x094
+#define AON_BACKUP6     0x098
+#define AON_BACKUP7     0x09C
+#define AON_BACKUP8     0x0A0
+#define AON_BACKUP9     0x0A4
+#define AON_BACKUP10    0x0A8
+#define AON_BACKUP11    0x0AC
+#define AON_BACKUP12    0x0B0
+#define AON_BACKUP13    0x0B4
+#define AON_BACKUP14    0x0B8
+#define AON_BACKUP15    0x0BC
+
+#define AON_PMUWAKEUPI0 0x100
+#define AON_PMUWAKEUPI1 0x104
+#define AON_PMUWAKEUPI2 0x108
+#define AON_PMUWAKEUPI3 0x10C
+#define AON_PMUWAKEUPI4 0x110
+#define AON_PMUWAKEUPI5 0x114
+#define AON_PMUWAKEUPI6 0x118
+#define AON_PMUWAKEUPI7 0x11C
+#define AON_PMUSLEEPI0  0x120
+#define AON_PMUSLEEPI1  0x124
+#define AON_PMUSLEEPI2  0x128
+#define AON_PMUSLEEPI3  0x12C
+#define AON_PMUSLEEPI4  0x130
+#define AON_PMUSLEEPI5  0x134
+#define AON_PMUSLEEPI6  0x138
+#define AON_PMUSLEEPI7  0x13C
+#define AON_PMUIE       0x140
+#define AON_PMUCAUSE    0x144
+#define AON_PMUSLEEP    0x148
+#define AON_PMUKEY      0x14C
+
+#define AON_LFROSC      0x070
+/* Constants */
+
+#define AON_WDOGKEY_VALUE  0x51F15E
+#define AON_WDOGFEED_VALUE 0xD09F00D
+
+#define AON_WDOGCFG_SCALE       0x0000000F
+#define AON_WDOGCFG_RSTEN       0x00000100
+#define AON_WDOGCFG_ZEROCMP     0x00000200
+#define AON_WDOGCFG_ENALWAYS    0x00001000
+#define AON_WDOGCFG_ENCOREAWAKE 0x00002000
+#define AON_WDOGCFG_CMPIP       0x10000000
+
+#define AON_RTCCFG_SCALE     0x0000000F
+#define AON_RTCCFG_ENALWAYS  0x00001000
+#define AON_RTCCFG_CMPIP     0x10000000
+
+#define AON_WAKEUPCAUSE_RESET   0x00
+#define AON_WAKEUPCAUSE_RTC     0x01
+#define AON_WAKEUPCAUSE_DWAKEUP 0x02
+#define AON_WAKEUPCAUSE_AWAKEUP 0x03
+
+#define AON_RESETCAUSE_POWERON  0x0000
+#define AON_RESETCAUSE_EXTERNAL 0x0100
+#define AON_RESETCAUSE_WATCHDOG 0x0200
+
+#define AON_PMUCAUSE_WAKEUPCAUSE 0x00FF
+#define AON_PMUCAUSE_RESETCAUSE  0xFF00
+
+#endif /* _SIFIVE_AON_H */

bare-metal-bsp/include/sifive/devices/clic.h

@@ -0,0 +1,30 @@
+// See LICENSE for license details.
+
+#ifndef _SIFIVE_CLIC_H
+#define _SIFIVE_CLIC_H
+
+#define CLIC_HART0          0x00800000
+#define CLIC_MSIP           0x0000
+#define CLIC_MSIP_size      0x4
+#define CLIC_MTIMECMP       0x4000
+#define CLIC_MTIMECMP_size  0x8
+#define CLIC_MTIME          0xBFF8
+#define CLIC_MTIME_size     0x8
+
+#define CLIC_INTIP          0x000
+#define CLIC_INTIE          0x400
+#define CLIC_INTCFG         0x800
+#define CLIC_CFG            0xc00
+
+// These interrupt IDs are consistent across old and new mtvec modes
+#define SSIPID              1
+#define MSIPID              3
+#define STIPID              5
+#define MTIPID              7
+#define SEIPID              9
+#define MEIPID              11
+#define CSIPID              12
+#define LOCALINTIDBASE      16
+
+
+#endif /* _SIFIVE_CLIC_H */ 

bare-metal-bsp/include/sifive/devices/clint.h

@@ -0,0 +1,14 @@
+// See LICENSE for license details
+
+#ifndef _SIFIVE_CLINT_H
+#define _SIFIVE_CLINT_H
+
+
+#define CLINT_MSIP 0x0000
+#define CLINT_MSIP_size   0x4
+#define CLINT_MTIMECMP 0x4000
+#define CLINT_MTIMECMP_size 0x8
+#define CLINT_MTIME 0xBFF8
+#define CLINT_MTIME_size 0x8
+
+#endif /* _SIFIVE_CLINT_H */ 

bare-metal-bsp/include/sifive/devices/gpio.h

@@ -0,0 +1,24 @@
+// See LICENSE for license details.
+
+#ifndef _SIFIVE_GPIO_H
+#define _SIFIVE_GPIO_H
+
+#define GPIO_INPUT_VAL  (0x00)
+#define GPIO_INPUT_EN   (0x04)
+#define GPIO_OUTPUT_EN  (0x08)
+#define GPIO_OUTPUT_VAL (0x0C)
+#define GPIO_PULLUP_EN  (0x10)
+#define GPIO_DRIVE      (0x14)
+#define GPIO_RISE_IE    (0x18)
+#define GPIO_RISE_IP    (0x1C)
+#define GPIO_FALL_IE    (0x20)
+#define GPIO_FALL_IP    (0x24)
+#define GPIO_HIGH_IE    (0x28)
+#define GPIO_HIGH_IP    (0x2C)
+#define GPIO_LOW_IE     (0x30)
+#define GPIO_LOW_IP     (0x34)
+#define GPIO_IOF_EN     (0x38)
+#define GPIO_IOF_SEL    (0x3C)
+#define GPIO_OUTPUT_XOR    (0x40)
+
+#endif /* _SIFIVE_GPIO_H */

bare-metal-bsp/include/sifive/devices/otp.h

@@ -0,0 +1,23 @@
+// See LICENSE for license details.
+
+#ifndef _SIFIVE_OTP_H
+#define _SIFIVE_OTP_H
+
+/* Register offsets */
+
+#define OTP_LOCK         0x00
+#define OTP_CK           0x04
+#define OTP_OE           0x08
+#define OTP_SEL          0x0C
+#define OTP_WE           0x10
+#define OTP_MR           0x14
+#define OTP_MRR          0x18
+#define OTP_MPP          0x1C
+#define OTP_VRREN        0x20
+#define OTP_VPPEN        0x24
+#define OTP_A            0x28
+#define OTP_D            0x2C
+#define OTP_Q            0x30
+#define OTP_READ_TIMINGS 0x34
+
+#endif

bare-metal-bsp/include/sifive/devices/plic.h

@@ -0,0 +1,31 @@
+// See LICENSE for license details.
+
+#ifndef PLIC_H
+#define PLIC_H
+
+#include <sifive/const.h>
+
+// 32 bits per source
+#define PLIC_PRIORITY_OFFSET            _AC(0x0000,UL)
+#define PLIC_PRIORITY_SHIFT_PER_SOURCE  2
+// 1 bit per source (1 address)
+#define PLIC_PENDING_OFFSET             _AC(0x1000,UL)
+#define PLIC_PENDING_SHIFT_PER_SOURCE   0
+
+//0x80 per target
+#define PLIC_ENABLE_OFFSET              _AC(0x2000,UL)
+#define PLIC_ENABLE_SHIFT_PER_TARGET    7
+
+
+#define PLIC_THRESHOLD_OFFSET           _AC(0x200000,UL)
+#define PLIC_CLAIM_OFFSET               _AC(0x200004,UL)
+#define PLIC_THRESHOLD_SHIFT_PER_TARGET 12
+#define PLIC_CLAIM_SHIFT_PER_TARGET     12
+
+#define PLIC_MAX_SOURCE                 1023
+#define PLIC_SOURCE_MASK                0x3FF
+
+#define PLIC_MAX_TARGET                 15871
+#define PLIC_TARGET_MASK                0x3FFF
+
+#endif /* PLIC_H */

bare-metal-bsp/include/sifive/devices/prci.h

@@ -0,0 +1,56 @@
+// See LICENSE for license details.
+
+#ifndef _SIFIVE_PRCI_H
+#define _SIFIVE_PRCI_H
+
+/* Register offsets */
+
+#define PRCI_HFROSCCFG   (0x0000)
+#define PRCI_HFXOSCCFG   (0x0004)
+#define PRCI_PLLCFG      (0x0008)
+#define PRCI_PLLDIV      (0x000C)
+#define PRCI_PROCMONCFG  (0x00F0)
+
+/* Fields */
+#define ROSC_DIV(x)    (((x) & 0x2F) << 0 ) 
+#define ROSC_TRIM(x)   (((x) & 0x1F) << 16)
+#define ROSC_EN(x)     (((x) & 0x1 ) << 30) 
+#define ROSC_RDY(x)    (((x) & 0x1 ) << 31)
+
+#define XOSC_EN(x)     (((x) & 0x1) << 30)
+#define XOSC_RDY(x)    (((x) & 0x1) << 31)
+
+#define PLL_R(x)       (((x) & 0x7)  << 0)
+// single reserved bit for F LSB.
+#define PLL_F(x)       (((x) & 0x3F) << 4)
+#define PLL_Q(x)       (((x) & 0x3)  << 10)
+#define PLL_SEL(x)     (((x) & 0x1)  << 16)
+#define PLL_REFSEL(x)  (((x) & 0x1)  << 17)
+#define PLL_BYPASS(x)  (((x) & 0x1)  << 18)
+#define PLL_LOCK(x)    (((x) & 0x1)  << 31)
+
+#define PLL_R_default 0x1
+#define PLL_F_default 0x1F
+#define PLL_Q_default 0x3
+
+#define PLL_REFSEL_HFROSC 0x0
+#define PLL_REFSEL_HFXOSC 0x1
+
+#define PLL_SEL_HFROSC 0x0
+#define PLL_SEL_PLL    0x1
+
+#define PLL_FINAL_DIV(x)      (((x) & 0x3F) << 0)
+#define PLL_FINAL_DIV_BY_1(x) (((x) & 0x1 ) << 8)
+
+#define PROCMON_DIV(x)   (((x) & 0x1F) << 0)
+#define PROCMON_TRIM(x)  (((x) & 0x1F) << 8)
+#define PROCMON_EN(x)    (((x) & 0x1)  << 16)
+#define PROCMON_SEL(x)   (((x) & 0x3)  << 24)
+#define PROCMON_NT_EN(x) (((x) & 0x1)  << 28)
+
+#define PROCMON_SEL_HFCLK     0
+#define PROCMON_SEL_HFXOSCIN  1
+#define PROCMON_SEL_PLLOUTDIV 2
+#define PROCMON_SEL_PROCMON   3
+
+#endif // _SIFIVE_PRCI_H

bare-metal-bsp/include/sifive/devices/pwm.h

@@ -0,0 +1,37 @@
+// See LICENSE for license details.
+
+#ifndef _SIFIVE_PWM_H
+#define _SIFIVE_PWM_H
+
+/* Register offsets */
+
+#define PWM_CFG   0x00
+#define PWM_COUNT 0x08
+#define PWM_S     0x10
+#define PWM_CMP0  0x20
+#define PWM_CMP1  0x24
+#define PWM_CMP2  0x28
+#define PWM_CMP3  0x2C
+
+/* Constants */
+
+#define PWM_CFG_SCALE       0x0000000F
+#define PWM_CFG_STICKY      0x00000100
+#define PWM_CFG_ZEROCMP     0x00000200
+#define PWM_CFG_DEGLITCH    0x00000400
+#define PWM_CFG_ENALWAYS    0x00001000
+#define PWM_CFG_ONESHOT     0x00002000
+#define PWM_CFG_CMP0CENTER  0x00010000
+#define PWM_CFG_CMP1CENTER  0x00020000
+#define PWM_CFG_CMP2CENTER  0x00040000
+#define PWM_CFG_CMP3CENTER  0x00080000
+#define PWM_CFG_CMP0GANG    0x01000000
+#define PWM_CFG_CMP1GANG    0x02000000
+#define PWM_CFG_CMP2GANG    0x04000000
+#define PWM_CFG_CMP3GANG    0x08000000
+#define PWM_CFG_CMP0IP      0x10000000
+#define PWM_CFG_CMP1IP      0x20000000
+#define PWM_CFG_CMP2IP      0x40000000
+#define PWM_CFG_CMP3IP      0x80000000
+
+#endif /* _SIFIVE_PWM_H */

bare-metal-bsp/include/sifive/devices/spi.h

@@ -0,0 +1,80 @@
+// See LICENSE for license details.
+
+#ifndef _SIFIVE_SPI_H
+#define _SIFIVE_SPI_H
+
+/* Register offsets */
+
+#define SPI_REG_SCKDIV          0x00
+#define SPI_REG_SCKMODE         0x04
+#define SPI_REG_CSID            0x10
+#define SPI_REG_CSDEF           0x14
+#define SPI_REG_CSMODE          0x18
+
+#define SPI_REG_DCSSCK          0x28
+#define SPI_REG_DSCKCS          0x2a
+#define SPI_REG_DINTERCS        0x2c
+#define SPI_REG_DINTERXFR       0x2e
+
+#define SPI_REG_FMT             0x40
+#define SPI_REG_TXFIFO          0x48
+#define SPI_REG_RXFIFO          0x4c
+#define SPI_REG_TXCTRL          0x50
+#define SPI_REG_RXCTRL          0x54
+
+#define SPI_REG_FCTRL           0x60
+#define SPI_REG_FFMT            0x64
+
+#define SPI_REG_IE              0x70
+#define SPI_REG_IP              0x74
+
+/* Fields */
+
+#define SPI_SCK_PHA             0x1
+#define SPI_SCK_POL             0x2
+
+#define SPI_FMT_PROTO(x)        ((x) & 0x3)
+#define SPI_FMT_ENDIAN(x)       (((x) & 0x1) << 2)
+#define SPI_FMT_DIR(x)          (((x) & 0x1) << 3)
+#define SPI_FMT_LEN(x)          (((x) & 0xf) << 16)
+
+/* TXCTRL register */
+#define SPI_TXWM(x)             ((x) & 0xffff)
+/* RXCTRL register */
+#define SPI_RXWM(x)             ((x) & 0xffff)
+
+#define SPI_IP_TXWM             0x1
+#define SPI_IP_RXWM             0x2
+
+#define SPI_FCTRL_EN            0x1
+
+#define SPI_INSN_CMD_EN         0x1
+#define SPI_INSN_ADDR_LEN(x)    (((x) & 0x7) << 1)
+#define SPI_INSN_PAD_CNT(x)     (((x) & 0xf) << 4)
+#define SPI_INSN_CMD_PROTO(x)   (((x) & 0x3) << 8)
+#define SPI_INSN_ADDR_PROTO(x)  (((x) & 0x3) << 10)
+#define SPI_INSN_DATA_PROTO(x)  (((x) & 0x3) << 12)
+#define SPI_INSN_CMD_CODE(x)    (((x) & 0xff) << 16)
+#define SPI_INSN_PAD_CODE(x)    (((x) & 0xff) << 24)
+
+#define SPI_TXFIFO_FULL  (1 << 31)   
+#define SPI_RXFIFO_EMPTY (1 << 31)   
+
+/* Values */
+
+#define SPI_CSMODE_AUTO         0
+#define SPI_CSMODE_HOLD         2
+#define SPI_CSMODE_OFF          3
+
+#define SPI_DIR_RX              0
+#define SPI_DIR_TX              1
+
+#define SPI_PROTO_S             0
+#define SPI_PROTO_D             1
+#define SPI_PROTO_Q             2
+
+#define SPI_ENDIAN_MSB          0
+#define SPI_ENDIAN_LSB          1
+
+
+#endif /* _SIFIVE_SPI_H */

bare-metal-bsp/include/sifive/devices/uart.h

@@ -0,0 +1,27 @@
+// See LICENSE for license details.
+
+#ifndef _SIFIVE_UART_H
+#define _SIFIVE_UART_H
+
+/* Register offsets */
+#define UART_REG_TXFIFO         0x00
+#define UART_REG_RXFIFO         0x04
+#define UART_REG_TXCTRL         0x08
+#define UART_REG_RXCTRL         0x0c
+#define UART_REG_IE             0x10
+#define UART_REG_IP             0x14
+#define UART_REG_DIV            0x18
+
+/* TXCTRL register */
+#define UART_TXEN               0x1
+#define UART_TXWM(x)            (((x) & 0xffff) << 16)
+
+/* RXCTRL register */
+#define UART_RXEN               0x1
+#define UART_RXWM(x)            (((x) & 0xffff) << 16)
+
+/* IP register */
+#define UART_IP_TXWM            0x1
+#define UART_IP_RXWM            0x2
+
+#endif /* _SIFIVE_UART_H */

bare-metal-bsp/include/sifive/sections.h

@@ -0,0 +1,17 @@
+// See LICENSE for license details.
+#ifndef _SECTIONS_H
+#define _SECTIONS_H
+
+extern unsigned char _rom[];
+extern unsigned char _rom_end[];
+
+extern unsigned char _ram[];
+extern unsigned char _ram_end[];
+
+extern unsigned char _ftext[];
+extern unsigned char _etext[];
+extern unsigned char _fbss[];
+extern unsigned char _ebss[];
+extern unsigned char _end[];
+
+#endif /* _SECTIONS_H */

bare-metal-bsp/include/sifive/smp.h

@@ -0,0 +1,65 @@
+#ifndef SIFIVE_SMP
+#define SIFIVE_SMP
+
+// The maximum number of HARTs this code supports
+#ifndef MAX_HARTS
+#define MAX_HARTS 32
+#endif
+#define CLINT_END_HART_IPI CLINT_CTRL_ADDR + (MAX_HARTS*4)
+
+// The hart that non-SMP tests should run on
+#ifndef NONSMP_HART
+#define NONSMP_HART 0
+#endif
+
+/* If your test cannot handle multiple-threads, use this: 
+ *   smp_disable(reg1)
+ */
+#define smp_disable(reg1, reg2)			 \
+  csrr reg1, mhartid				;\
+  li   reg2, NONSMP_HART			;\
+  beq  reg1, reg2, hart0_entry			;\
+42:						;\
+  wfi    					;\
+  j 42b						;\
+hart0_entry:
+
+/* If your test needs to temporarily block multiple-threads, do this:
+ *    smp_pause(reg1, reg2)
+ *    ... single-threaded work ...
+ *    smp_resume(reg1, reg2)
+ *    ... multi-threaded work ...
+ */
+
+#define smp_pause(reg1, reg2)	 \
+  li reg2, 0x8			;\
+  csrw mie, reg2		;\
+  csrr reg2, mhartid		;\
+  bnez reg2, 42f
+
+#define smp_resume(reg1, reg2)	 \
+  li reg1, CLINT_CTRL_ADDR	;\
+41:				;\
+  li reg2, 1			;\
+  sw reg2, 0(reg1)		;\
+  addi reg1, reg1, 4		;\
+  li reg2, CLINT_END_HART_IPI	;\
+  blt reg1, reg2, 41b		;\
+42:				;\
+  wfi    			;\
+  csrr reg2, mip		;\
+  andi reg2, reg2, 0x8		;\
+  beqz reg2, 42b		;\
+  li reg1, CLINT_CTRL_ADDR	;\
+  csrr reg2, mhartid		;\
+  slli reg2, reg2, 2		;\
+  add reg2, reg2, reg1		;\
+  sw zero, 0(reg2)		;\
+41:				;\
+  lw reg2, 0(reg1)		;\
+  bnez reg2, 41b		;\
+  addi reg1, reg1, 4		;\
+  li reg2, CLINT_END_HART_IPI	;\
+  blt reg1, reg2, 41b
+
+#endif

bare-metal-bsp/libwrap/libwrap.mk

@@ -32,7 +32,6 @@ LIBWRAP_SRCS := $(foreach f,$(LIBWRAP_SRCS),$(LIBWRAP_DIR)/$(f))
 LIBWRAP_OBJS := $(LIBWRAP_SRCS:.c=.o)
 
 LIBWRAP_SYMS := \
-	malloc \
 	open \
 	lseek _lseek\
 	read _read\

bare-metal-bsp/libwrap/sys/_exit.c

@@ -16,7 +16,9 @@ void __wrap__exit(int code)
   write(STDERR_FILENO, message, sizeof(message) - 1);
   write_hex(STDERR_FILENO, code);
   write(STDERR_FILENO, "\n", 1);
+#ifdef USE_TOHOST
   tohost = code+1;
+#endif
   write(STDERR_FILENO, "\x04", 1);
   for (;;);
 }

bare-metal-bsp/libwrap/sys/read.c

@@ -12,8 +12,8 @@
 ssize_t __wrap_read(int fd, void* ptr, size_t len)
 {
   uint8_t * current = (uint8_t *)ptr;
-  volatile uint32_t * uart_rx = (uint32_t *)(UART0_BASE_ADDR + UART_REG_RXFIFO);
+  volatile uint32_t * uart_rx = (uint32_t *)(UART0_CTRL_ADDR + UART_REG_RXFIFO);
-  volatile uint8_t * uart_rx_cnt = (uint8_t *)(UART0_BASE_ADDR + UART_REG_RXCTRL + 2);
+  volatile uint8_t * uart_rx_cnt = (uint8_t *)(UART0_CTRL_ADDR + UART_REG_RXCTRL + 2);
 
   ssize_t result = 0;
 
@@ -30,4 +30,3 @@ ssize_t __wrap_read(int fd, void* ptr, size_t len)
   return _stub(EBADF);
 }
 weak_under_alias(read);
-