As per RISC-V privilege specification, a platform may choose to implement
a coarser granularity scheme for PMP addresses. In that case, we shouldn't
allow any pmp region size smaller than the platform supports. A platform
may not also implement all the bits for a PMP address specified in the priv
specification.
The pmp range granularity and address bits should be detected dynamically
before detecing PMP regions. Any pmp modification request beyond these detected
value must not succeed.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
We extend boot prints to display details of each domain. In the
process, we remove sbi_hart_pmp_dump() because it shows redundant
information which domain details already show.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
The PMP configuration on each HART should be only based on the memory
regions of the assigned domain because each domain includes a memory
region to protect the underlying firmware.
This patch updates the sbi_hart_pmp_configure() function accordingly.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
The sbi_hart_pmp_get() and sbi_hart_pmp_check_addr() functions
are not used anymore hence this patch removes these functions.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
The sbi_system_reset() should issue platform system reset only if
domain of current HART is allowed to do system reset.
This patch extends sbi_system_reset() as-per above.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Instead of calling sbi_hsm_hart_get_state() in a loop, we can simply
call a new inline __sbi_hsm_hart_get_state() which only takes "hartid"
and enforce domain checks using sbi_domain_assigned_hartmask().
This patch optimizes sbi_hsm_hart_started_mask() as-per above.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
The sbi_hsm_hart_start() should consider the domain under which we
are trying to start the HART. This will help ensure that HART A can
start HART B only if both HARTs A and B belong to the same domain.
We also have a special case when we bring-up boot HART of non-root
domains in sbi_domain_finalize() where we should skip domain checks
in sbi_hsm_hart_start(). To achieve this, sbi_hsm_hart_start() should
do domain checks only when domain parameter is non-NULL.
This patch extends sbi_hsm_hart_start() as-per above.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
The sbi_hsm_hart_started_mask() API should take one more parameter
to allow caller specify domain under which started_mask is being
generated. Further, the sbi_hsm_hart_started_mask() depends on
sbi_hsm_hart_get_state() which also should return HART state under
specified domain.
This patch updates both sbi_hsm_hart_started_mask() and
sbi_hsm_hart_get_state() as-per above.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
An OpenSBI domain is a logical entity representing a set of HARTs
and a set of memory regions for these HARTs.
The OpenSBI domains support will allow OpenSBI platforms and previous
booting stage (i.e. U-Boot SPL, Coreboot, etc) to partition a system
into multiple domains where each domain will run it's own software.
For inter-domain isolation, OpenSBI will eventually use various HW
features such as PMP, ePMP, IOPMP, SiFive shield, etc but initial
implementation only use HW PMP support.
This patch provides initial implementation of OpenSBI domains where
we have a root/default domain and OpenSBI platforms can provide
non-root/custom domains using domain_get() callback.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
The hartid parameter of sbi_hart_init() is not used anywhere in
sbi_hart_init() implementation so let's remove it.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
We factor-out PMP configuration from sbi_hart_init() as a separate
sbi_hart_pmp_configure() function and do the PMP configuration very
late in coldboot and warmboot path just before platform_final_init().
Eventually, this enable us to configure PMP totally based on OpenSBI
domain where OpenSBI domains can be parsed from device-tree in any of
the platform operations except platform_final_init().
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
The pmp_region_xyz() callbacks are not required in sbi_platform_operations
because we will be using OpenSBI domain memory regions to program the
PMP CSRs.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
The sbi_ecall.h and sbi_trap.h are not required to be included in
sbi_platform.h hence we remove it. This way sources requiring
these headers will have to explicitly include it thereby reducing
implicit includes.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
HiFive unleashed currently implements fewer than 56 bits of physical
address so existing PMP CSR detection is broken.
PMP address register encodes bits 55-2 of a 56-bit physical address,
Not all physical address bits may be implemented, So just check
minimum 1 bit.
Fixes: 74d1db7062 ("lib: sbi: Improve PMP CSR detection and
progamming")
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
The coldboot HART jumps to the next booting stage at the end of
init_coldboot() so it is absolutely necessary for coldboot HART
to support the privilege mode expected by the next booting stage.
We extend the coldboot HART selection in sbi_init() to ensure that
the selected coldboot HART always supports privilege mode specified
in scratch space (i.e. scratch->next_mode). This will further help
us allow E-core (without MMU) on SiFive Unleashed and PolarFire
ICICLE boards to proceed further and wait in HSM STOPPED state.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
We extend sbi_hart_pmp_check_addr() API so that users can specify
privilege mode of the address for checking PMP access permissions.
To achieve this, we end-up converting "unsigned long *size" parameter
to "unsigned long *log2len" for pmp_get() implementation so that we
can deal with regions of "1UL << __riscv_xlen" size in a special case
in sbi_hart_pmp_check_addr() implementation.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
The sbi_scratch already has provision to specify the next stage mode
so we can leverage this to specify start mode to sbi_hsm_hart_start().
In future, this will be useful in providing SBI calls to U-mode on
embedded cores where we M-mode and U-mode but no S-mode.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
We should allow M-mode to M-mode ECALLs because:
1. No other mode can handle M-mode ECALLs
2. In future, we can allow M-mode baremetal application (not
linked to OpenSBI) running independently and cooperatively
without corrupting OpenSBI M-mode state (CSRs and memory).
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
We rename CAUSE_HYPERVISOR_ECALL to CAUSE_SUPERVISOR_ECALL and
CAUSE_SUPERVISOR_ECALL to CAUSE_VIRTUAL_SUPERVISOR_ECALL so that
it matches latest RISC-V privilege spec.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
The VS-mode ecall is supposed to be handled by HS-mode so
sbi_trap_handler() should fallback to default case for
VS-mode ecall trap.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
We improve HPM CSR read/write emulation as follows:
1. Fail for unimplemented counters so that trap is redirected
to S-mode which can further help debugging S-mode software.
2. Check permissions in both MCOUNTEREN and SCOUNTEREN for
HS-mode and U-mode.
3. Don't check permissions for TIME CSR because we emulate
TIME CSR for both Host (HS/U-mode) and Guest (VS/VU-mode).
Also, faster TIME CSR read is very helpful for good
performance of S-mode software.
4. Don't emulate S-mode CSR read/write to M-mode HPM CSRs
because these should not be accessible to S-mode software.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
A RISC-V platform can leave unimplemented MHPM counters hard-wired
to zero. We extend hart_detect_features() to detect MHPM counters
which are accessible and not hard-wired to zero. We also print
number of available MHPM counters as part of boot prints.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
As-per latest RISC-V privilege spec up to 64 PMP entries are supported.
Implementations may implement zero, 16, or 64 PMP CSRs. All PMP CSR
fields are WARL and may be hardwired to zero.
This patch improves PMP CSR detection and progamming considering
above facts.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
The SBI_HART_HAS_PMP feature is redundant because we already
have number of PMP regions returned by sbi_hart_pmp_count().
Checking whether PMP is supported for a HART can be simply done
by checking non-zero value returned by sbi_hart_pmp_count().
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
The Kendryte K210 follows RISC-V v1.9 spec so MTVAL has instruction
address (instead of instruction encoding) on illegal instruction trap.
To handle above case, we fix sbi_illegal_insn_handler() without any
impact on RISC-V v1.10 (or higher) systems. This achieved by exploiting
the fact that program counter (and instruction address) is always 2-byte
aligned in RISC-V world.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
We can have thundering hurd problem with coldboot_lock where the
boot HART can potentially starve trying to acquire coldboot_lock
because some of the non-boot HARTs are continuously acquiring and
releasing coldboot_lock. This can happen if MIP.MSIP bit is already
set for some of the non-boot HARTs.
To avoid thundering hurd problem for coldboot_lock, we use the
__smp_load_acquire() and __smp_store_release() for coldboot_done
flag and use coldboot_lock only for coldboot_wait_hmask.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
When redirecting from VS/VU-mode to HS-mode, hstatus.SPVP was set
to the value of mstatus.SPP, as according to the specification both
flags should be set to the same value.
However, the assignment of SPVP takes place before SPP itself is
updated, which results in SPVP having an outdated value.
Signed-off-by: Georg Kotheimer <georg.kotheimer@tu-dresden.de>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
If MTINST[0:0] bit is 1 then we have transformed instruction encoding
in MTINST CSR. For transformed instructions, if the MTINST[1:1] bit
is Zero then original trapped instruction was a 16bit instruction
which was converted to 32bit instruction at time of taking trap.
We should use MTINST[1:1] bit to determine correct instruction length
of transformed instruction.
This patch updates misaligned load/store emulation as-per above.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
We should only return valid error codes from SBI ecalls as
defined by the RISC-V SBI spec.
To achieve this:
1. We use SBI_Exxxx defines for OpenSBI internal errors with
error values starting from -1000
2. We use SBI_ERR_xxxx defines for errors defined by SBI spec
3. We map some of the SBI_Exxxx defines to SBI_ERR_xxxx defines
which are semantically same
4. We throw a error print and force return error code to
SBI_ERR_FAILED in sbi_ecall_handler() if we see an invalid
error code being returned to S-mode
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
On RV64,"unsigned long" is 64bit and "unsigned int" is 32bit. So in
function "pmp_get" and "pmp_set", if "pmpcfg_shift >= 32", "0xff << pmpcfg_shift"
will go beyond "unsigned int" width. This patch tries to fix this issue.
In function 'pmp_get':
cfgmask = (0xff << pmpcfg_shift);
-->
cfgmask = (0xffUL << pmpcfg_shift);
In function 'pmp_set':
cfgmask = ~(0xff << pmpcfg_shift);
-->
cfgmask = ~(0xffUL << pmpcfg_shift);
Signed-off-by: Liush <liush.damon@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
The arguments/parameters of __sbi_hfence_gvma_vmid_gpa() and
__sbi_hfence_vvma_asid_va() functions are swapped so we fix it.
Currently, we did not face any issues because QEMU does a full
TLB flush for all HFENCE instructions.
We also improve documentation of HFENCE.GVMA and HFENCE.VVMA
instruction encoding.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
To support RISC-V hypervisor v0.6.1, we:
1. Don't need to explicitly forward WFI traps from VS/VU-mode
2. Have to delegate virtual instruction trap to HS-mode
3. Have to update trap redirection for changes in HSTATUS CSR
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
It is not mandatory for a RISC-V systems to implement all PMP
regions so we have to check all PMPADDRx CSRs to determine excat
number of supported PMP regions.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
This patch does few cosmetic improvements to HART feature detection:
1. Remove sbi_ perfix from HART feature detection functions
because all local/static functions in sbi_hart.c don't have
sbi_ prefix
2. Remove sbi_hart_set_feature() because it's quite small and
local/static in sbi_hart.c
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
It makes more sense to have scratch pointer as parameter in
HART feature APIs because:
1. We already have scratch pointer at places where these APIs
are used.
2. This is consistent with lot of other APIs in sbi_hart.h
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
On platforms with continuous HART ids starting from zero:
0 <= boot HART id < platform HART count
The above co-relation of boot HART id and platform HART count
is true for most RISC-V platfors so it's better to print platform
HART count just before boot HART id.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
We do following improvements for get_feature_str():
1. We should return "none" from get_feature_str() no features
available instead of sbi_boot_prints() explicitly handling
failure.
2. We don't need to return failure (just like misa_xlen())
because we are returning "none" for no features and we are
truncating output when space is not available.
3. Based on 1 and 2, the sbi_boot_prints() can be further
simplified.
4. No need for two char[] in sbi_boot_prints()
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
We should detect HART features in sbi_hart_init() before
mstatus_init(), delegate_traps() and pmp_init().
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
Currently, unprivileged access functions uses few additional instructions
which are redundant. It also uses specific registers which are not necessary.
Remove those additional instructions and let the compiler choose the
registers.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
We have now clear distinction between platform and hart features.
Modify the boot print messages to print hart specific features in
a string format.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Tested-by: Jonathan Balkind <jbalkind@cs.princeton.edu>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
We have now clear distinction between platform and hart features.
Modify the boot print messages to print platform features in a string
format. In the process, this patch moved relatively larger functions
to its own file from platform.h header file.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Tested-by: Jonathan Balkind <jbalkind@cs.princeton.edu>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
As per the RISC-V specification, time value can be obtained from a time
CSR implemented in hardware or a MMIO based IP block. Qemu virt machine
already supports timer csr while CLINT provides the timer for other
platforms.
Implement a hart specific timer feature that can be detected at runtime.
As CSR based timer implementation are faster than MMIO address based, it
is always preferred over MMIO based one.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Tested-by: Jonathan Balkind <jbalkind@cs.princeton.edu>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
PMP & performance counters belong to a hart rather than a platform.
In addition to that, these features enable reading/writing from a
particular csr. Thus, they can be detected and set at runtime rather
than compile time.
Move PMP/MCOUNTEREN/SCOUNTEREN features to hart and detect them at runtime.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Tested-by: Jonathan Balkind <jbalkind@cs.princeton.edu>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
There may be some features which are hart specific rather than a platform
specific feature. Add a framework to support that.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Tested-by: Jonathan Balkind <jbalkind@cs.princeton.edu>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
There may be few common mathematics helper functions which can be used
anywhere in OpenSBI project.
Add a separate math helper function file to add these functions.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Unprivileged trap handler can be reused for any cases where the executing
code expects a trap.
Rename it to "expected" trap handler as it will be used in other cases in
future.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Tested-by: Jonathan Balkind <jbalkind@cs.princeton.edu>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
