This patch updates OpenSBI version to 1.5 as part of
release preparation.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Anup Patel <anup@brainfault.org>
Current Debug Trigger SBI extension proposal suggests to activate
shmem area and obtain its physical address from S-mode software
in the following way:
: If both `shmem_phys_lo` and `shmem_phys_hi` parameters are not
: all-ones bitwise then `shmem_phys_lo` specifies the lower XLEN
: bits and `shmem_phys_hi` specifies the upper XLEN bits of the
: shared memory physical base address. The `shmem_phys_lo` MUST
: be `(XLEN / 8)` byte aligned and the size of shared memory is
: assumed to be `trig_max * (XLEN / 2)` bytes.
For more details see the current version of the proposal:
- https://lists.riscv.org/g/tech-debug/message/1302
On the other hand, on RV32, the M-mode can only access the first 4GB of
the physical address space because M-mode does not have MMU to access
full 34-bit physical address space. Similarly, on RV64, the M-mode can
only access memory addressed by 64 bits.
This commit checks shmem address in function sbi_dbtr_setup_shmem
to make sure that shmem_phys_hi part of the valid address is zero.
Besides, the macro DBTR_SHMEM_MAKE_PHYS is updated to take into
account only low XLEN part.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Reviewed-by: Himanshu Chauhan <hchauhan@ventanamicro.com>
Error code returned by the ecall handles should use the defines from
sbi_ecall_interface.h rather than sbi_error.h.
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
As stated by the spec and pointed out by Andrew Jones, the value passed
for MISALIGNED_EXC_DELEG and PTE_AD_HW_UPDATING should be either 0 or 1.
Add check for these values and return SBI_EINVAL if not.
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The SBI FWFT extension defines a set of function that can be called
to control the configuration of some platform features (misaligned
trap delegation, etc). This patch implements sbi_fwft_set() and
sbi_fwft_get() as defined in the specification [1].
Link: https://lists.riscv.org/g/tech-prs/message/924 [1]
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Add support for SBI_FWFT_PTE_AD_HW_UPDATING based on SVADU presence.
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Add support for SBI_FWFT_MISALIGNED_EXC_DELEG withing FWFT support. This
support allows to delegate misaligned accesses traps.
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Add support for Svade and Svadu extensions. When both are present in the
device tree, the M-mode firmware should select the Svade extension
to comply with the RVA23 profile, which mandates Svade and lists Svadu as
an optional extension.
Signed-off-by: Yong-Xuan Wang <yongxuan.wang@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Like PMP, the behaviors to configure PMA will be different from
RV64 and RV32. RV64 uses two Andes custom CSRs, pmacfg0 and pmacfg2,
but RV32 uses four Andes custom CSRs, pmacfg0 ~ pmacfg3. This patch
adds support to PMA for RV32.
Signed-off-by: Ben Zong-You Xie <ben717@andestech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
This patch refines the Andes PMA related code. The main change is
refactor andes_pma_[read|write]_cfg() and andes_pma_[read|write]_addr()
into new functions andes_pma_[read|write]_num().
Also, fix some coding style problems.
Signed-off-by: Ben Zong-You Xie <ben717@andestech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
When used to read characters from the terminal (e.g., when the SBI
console is used via ecall from linux with `console=hvc0`), we must
acknowledge receipt of each character to "pop" it off the LiteUART
hardware queue, and allow the next character to be made available.
Fixes: 52af6e4b ("lib: utils: Add LiteX UART support")
Suggested-by: Dolu1990 <charles.papon.90@gmail.com>
Signed-off-by: Gabriel Somlo <gsomlo@gmail.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
In DT, multiple reset devices may use the same driver, and they
may have different priorities. If rc is returned after the first
initialization, the highest priority device may be lost.
Fixes: a73ff043e9 (lib: utils/reset: Fix fdt_reset to search for more dt nodes)
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
If there are multiple dt nodes, the previous code only tries to match
the first one, which may lose initialization.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
When the dt node has a status property and the value is not ok or
okay, skip initializing reset.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
If there are multiple dt nodes, the previous code only tries to match
the first one, which may lose initialization.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
When the dt node has a status property and the value is not ok or
okay, skip initializing serial.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
When the dt node has a status property and the value is not ok or
okay, skip initializing irqchip.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
When the dt node has a status property and the value is not ok or
okay, skip initializing timer.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
When the dt node has a status property and the value is not ok or
okay, skip initializing ipi.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
During Linux AIA driver review, the APLIC DT property for interrupt
delegation was renamed to "riscv,delegation" so let's use the new DT
property name and fallback to old DT property name if the new DT
property name is not available.
Fixes: 34612193af ("lib: utils/irqchip: Add FDT based driver for APLIC")
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
"gpio-poweroff" and "gpio-restart" always set gpio to high to
active the function, but some chips need a low signal to active.
Fortunately, it can be achieved by setting GPIO_FLAG_ACTIVE_LOW
for the gpio. Implement this flag support for the gpio library
so the gpio reset can function well.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The spec states that a6, a7, flags and sepc are writable but the
implementation was not allowing that. Add support for these 4 writable
attributes.
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Reviewed-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Add extra sanity checks to prevent the caller getting the invalid result from
imsic_get_data() or imsic_get_target_file() when imsic is not initialized
correctly.
Signed-off-by: Cyan Yang <cyan.yang@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Bring back FW_TEXT_START as an optional parameter to allow users
explicitly specify compile time address for loading debug symbols.
When not specified, the FW_TEXT_START is assumed to be 0.
Fixes: d4d2582eef ("firmware: remove FW_TEXT_START")
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Tested-by: Clément Léger <cleger@rivosinc.com>
The current mlevel imsic check is only for the platform, which
may cause hart without imsic in the platform to trigger an
illegal instruction exception when initializing imsic. For
example, the platform contains a management hart that only
supports wired interrupts.
This patch will check if each hart supports Smaia extension
before doing imsic initialization to avoid triggering illegal
instruction exceptions.
Signed-off-by: Cheng Yang <yangcheng.work@foxmail.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The Sophgo CV18XX/SG200X series SoCs have a standard C906
core. Add support for it.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Currently, the sbi_sse_exit() gets event in a loop but does not put
it back after use. This results in global events remaining locked
causing hangs on sub-sequent calls to sse_event_get() for global
events.
Fixes: c8cdf01d8f ("lib: sbi: Add support for Supervisor Software Events extension")
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Himanshu Chauhan <hchauhan@ventanamicro.com>
SG2042 uses an onboard MCU to provide reset function.
Add reset driver to support this onboard MCU.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The inline function can simplify the code by setting some call
restrictions. This ensures logical smoothness
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Modify the return value of the sbi_dbtr_shmem_disabled function to
bool to make the semantics clearer.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The previous code detected shmem_phys_hi and shmem_phys_lo as two
addresses. fix this bug
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Himanshu Chauhan <hchauhan@ventanamicro.com>
Obtaining a 64-bit address under rv64 does not require combining
32-bit registers
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Himanshu Chauhan <hchauhan@ventanamicro.com>
After getting hart_shmem_base, dbtr_thishart_state_ptr cannot be
empty. So remove check code.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Himanshu Chauhan <hchauhan@ventanamicro.com>
When only phys_hi is equal to SBI_DBTR_SHMEM_INVALID_ADDR, it may be
a legal address. The old code would modify the legal address.
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Himanshu Chauhan <hchauhan@ventanamicro.com>
As Guo Ren said from the kernel mailing list [1], future T-Head CPUs,
including the newer versions of T-Head C908, will feature standard
Sscofpmf extension. For these CPUs, T-Head's implementation of PMU
Overflow Interrupts may not needed anymore. In this case, we shouldn't
apply T-Head PMU for all T-Head CPUs. Thus, this patch separated T-Head PMU
errata.
[1] https://lore.kernel.org/linux-riscv/Zh9sUUUT09LZb0MO@gmail.com/
Signed-off-by: Yangyu Chen <cyy@cyyself.name>
Reviewed-by: Inochi Amaoto <inochiama@outlook.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
To make the framework suit all Andes CPUs, change all occurrences of
andes45 to andes.
In addition, we fix some coding style problems and remove an unused
macro in andes.h.
Signed-off-by: Ben Zong-You Xie <ben717@andestech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Add spinlock protection to avoid race condition on assigned_harts
during domain context switching. Also, rename/add variables for
accessing the corresponding domain of target/current context.
Signed-off-by: Alvin Chang <alvinga@andestech.com>
Reviewed-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Although Mstatus.MPV is set, before executing mret, access to VS mode
registers should use the actual register addresses, not the pseudonyms
of S registers.
Signed-off-by: Pope B.Lei <popeblei@gmail.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
When registering an SSE event, check for the handler_entry_pc to belong
to supervisor mode domain using sbi_domain_check_addr_range().
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Reported-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Rather then passing 1 to sbi_domain_check_addr_range() for supervisor
mode, use PRV_S.
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Move the enable callback call before sending the IPI. Even though the
event is locked and no race condition can happen, this is more logical.
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Reported-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The list loop below that check is actually not looping if the list is
empty so there was no need for this check.
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Reported-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Rather than checking 32bits overflow with some absolute value, check the
value to be different from the cast itself.
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Reported-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
There was a naming incoherency between enabled events list lock/unlock.
Rename sse_hart_unlock() to sse_enabled_event_unlock() to be coherent
and reword comments above lock()/unlock() functions.
Signed-off-by: Clément Léger <cleger@rivosinc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
