Add psuedoinstruction encodings written to mtinst/htinst for faults
caused by implicit memory access for VS-stage address translation
Signed-off-by: dramforever <dramforever@live.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The delegation bit is lost along with the rest of the PLIC state when
the CPU power domain in the Allwinner D1 is powered down, so the PLIC
needs to be re-delegated to S-mode during the hart resume path.
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
These functions save/restore the state of the PLIC associated with the
current hart. The context save/restore functions only manipulate a
single context, since most likely the M-mode context is unused and does
not need to be saved.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
These can be used by platform code to save the PLIC priority state, if
it would otherwise be lost during non-retentive suspend. The platform
is responsible for allocating all necessary storage.
As a space optimization, store the saved priority values as 8-bit
integers, since that is large enough to hold any priority value on the
relevant platforms.
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
These can be used by platform code to save the PLIC context state, if
it would otherwise be lost during non-retentive suspend. The platform
is responsible for allocating all necessary storage.
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
This simplifies both the callers and the callees by removing duplicated
code and consolidating the error handling. It also fixes two bugs in the
process:
1) ie_words was one too large when plic->num_src was a multiple of 32.
2) plic_set_ie takes a 32-bit mask, not a Boolean value, so the FPGA
platforms previously only enabled one out of every 32 interrupts.
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
None of the functions modify the passed-in plic_data, so mark it const.
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
The suspend code needs to know the resume address for two reasons:
1) Programming some hardware register or management firmware. Here we
assume the hardware/firmware maintains its state between suspends,
so it only needs to be programmed once at startup.
2) When a non-retentive suspend request ends up being retentive, due
to lack of hardware support, pending interrupt, or for some other
reason. However, the behavior here is not platform-dependent, and
this can be handled in the generic hart suspend function.
Since neither situation requires the platform-level suspend function to
know the resume address, stop passing it to that function. Instead,
handle the non-retentive to retentive situation generically.
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Non-retentive suspend states may require platform-specific actions
during resume. For example, firmware may need to save and restore the
values of custom CSRs. Add a hook to support this.
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Match data stores hardware attributes which do not change at runtime, so
it does not need to be mutable. Make it const.
Reviewed-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
The function returns the highest hart-id of the harts actually used in
the system (enabled). Change the name to reflect this fact.
Signed-off-by: Jan Remes <jan.remes@codasip.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
If an FDT node contains a "status" property and this property is not
"ok" or "okay", this node should be ignored. Introduce a function that
checks this.
Signed-off-by: Jan Remes <jan.remes@codasip.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Instead of having FDT gpio driver list hard-coded in the C source,
we generate it using carray.sh at compile-time.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
We add platform specific extensions_init() callback which allows
platforms to populate HART extensions for each HART. For example,
the generic platform can populate HART extensions from HART ISA
string described in DeviceTree.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
We add sbi_hart_update_extension() function which allow platforms
to enable/disable hart extensions.
Signed-off-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Since past few years, we have been using "hart features" in OpenSBI
to represent all optionalities and multi-letter extensions defined
by the RISC-V specifications.
The RISC-V profiles specification has taken a different approach and
started assigning extension names for all optionalities which did not
have any extension name previously.
(Refer, https://github.com/riscv/riscv-profiles/blob/main/profiles.adoc)
Inspired from the RISC-V profiles specification, we convert OpenSBI
hart features into hart extensions. Going forward, we align the
extension naming with RISC-V profiles specification. Currently, only
"time CSR" and "AIA CSR" have not been assigned extension name but
for everything else we have a name.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
If a hart implements privileged spec v1.12 (or higher) then we can
safely assume that menvcfg CSR is present and we don't need MENVCFG
as a hart feature.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
If a hart implements privileged spec v1.11 (or higher) then we can
safely assume that mcountinhibit CSR is present and we don't need
MCOUNTINHIBT as a hart feature.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
If a hart implements privileged spec v1.10 (or higher) then we can
safely assume that [m|s]counteren CSR are present and we don't need
MCOUNTEREN and SCOUNTEREN as hart features.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
It is possible to guess privileged spec versions based on the CSRs
that where introduced in different privileged spec versions. In
future, if we are not able guess privileged spec version then we
can have platform provide it.
We add privileged spec version as per-hart feature and try to guess
it based on presence of mcounteren, mcountinhibit, and menvcfg CSRs.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Recently, Sstc extension was ratified. It defines stimecmp which allows
the supervisor mode to directly update the timecmp value without the
need of the SBI call. The hardware also can inject the S-mode timer
interrupt direclty to the supervisor without going through the M-mode.
To maintain backward compatibility with the older software, SBI call
now uses stimecmp directly if the hardware supports.
Implement the Sstc extension.
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Accordind to the RISC-V privileged specification, the VS filed is
mstatus[10:9] instead of mstatus[24:23]. Modify the MSTATUS_VS
to the correct value.
Reported-by: I-Cheng Cheng <i-cheng.cheng@sifive.com>
Signed-off-by: Vincent Chen <vincent.chen@sifive.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
reg-offset property is used for offset to apply to the mapbase
from the start of the registers in 8250 UART. In Linux kernel,
it has been handled in 8250 UART driver.
dt-bindings:
<linux>/Documentation/devicetree/bindings/serial/8250.yaml
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Extend HART feature detection to discover Smstateen CSRs at boot-time
and configure mstateen envcfg bit depending on availability of
menvcfg CSR.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Smstateen extension provides a mechanism to plug potential
covert channels which are opened by extensions that add to
processor state that may not get context-switched.
Signed-off-by: Mayuresh Chitale <mchitale@ventanamicro.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
We add the menvcfg CSR as a HART feature and detect it at boot time
using traping mechanism.
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Xiang W <wxjstz@126.com>
The latest RISC-V privileged specification introduces xenvcfg CSRs
to enable/disable certain features/extensions for lower privilege
modes. This patch adds defines for these new [m|h|s]envcfg CSRs.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Add static detection to prevent the modification of struct fw_dynamic_info
from forgetting the modification of FW_DYNAMIC_INFO_xxx_OFFSET
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Add static detection to prevent the modification of struct sbi_scratch
from forgetting the modification of SBI_SCRATCH_xxx_OFFSET
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Add static detection to prevent the modification of struct sbi_platform
from forgetting the modification of SBI_PLATFORM_xxx_OFFSET
Signed-off-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Initial commit of the xlnx-uartlite device and FDT support. This was
tested by running OpenSBI on a modified QEMU virt machine using the
xlnx-uartlite for serial.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Currently, the external interrupt handling is scattered between
sbi_init and sbi_trap. This patch moves all external interrupt
handling into a simple framework called sbi_irqchip.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
We should disable APLIC DT nodes in fdt_fixups() which are not
accessible to the next booting stage based on currently assigned
domain.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
We add simple FDT irqchip driver for APLIC so that generic platform (and
other FDT based platforms) can utilize common APLIC initialization library.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
We add simple APLIC initialization library which is independent of
hardware description format (FDT or ACPI). This APLIC initialization
library can be used by custom OpenSBI platform support to setup
APLIC domains.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
We should disable IMSIC DT nodes in fdt_fixups() which are not
accessible to the next booting stage based on currently assigned
domain.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
We add simple FDT irqchip driver for IMSIC so that generic platform
(and other FDT based platforms) can utilize common IMIC library.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
We add simple IMSIC library which is independent of hardware description
format (FDT or ACPI). This IMSIC library can be used by custom OpenSBI
platform support to setup IMSIC for external interrupts.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
We introduce nascent_init() platform callback which will allow
platforms to do very early initialization of platform specific
per-HART CSRs and per-HART devices.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
This patch adds sbi_trap_set_external_irqfn() API which can be used by
OpenSBI platform code to set a callback function for external interrupts.
The RISC-V AIA IMSIC driver will use this API to implement inter-processor
interrupts on-top-of MSIs.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
The RISC-V AIA specification improves handling of per-HART local
interrupts in a backward compatible manner. This patch adds defines
for the new RISC-V AIA CSRs.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
In a systems that provide strings.h and it is included
together with sbi_bitops.h the compilation error appears.
The ffs() and fls() are provided by strings.h
Signed-off-by: Petro Karashchenko <petro.karashchenko@gmail.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
PMU overflow interrupt should be disabled durinig initial configuration of
counters. They should be enabled while starting counters.
Fixes: 730f01bb41 ("lib: sbi: Support sscofpmf extension in OpenSBI")
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Using "void *" in arithmetic causes errors with strict compiler settings:
"error: pointer of type 'void *' used in arithmetic [-Werror=pointer-arith]"
Avoid these by calculating on "char *" where 1-byte data size is assumed.
Signed-off-by: Jukka Laitinen <jukkax@ssrc.tii.ae>
Reviewed-by: Dong Du <Dd_nirvana@sjtu.edu.cn>
Reviewed-by: Xiang W <wxjstz@126.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Some of RISC-V emulators provide HTIF at fixed base address so for
such emulators users have to hard-code HTIF base address in the
linker script.
To address this problem, we let users optionally provide fixed HTIF
base address via platform support (or device tree).
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Dong Du <Dd_nirvana@sjtu.edu.cn>
Reviewed-by: Atish Patra <atishp@rivosinc.com>
