The function starfive_jh7110_inst_init() initialize some power
management unit address and clock addresses, needed for the reset
driver. It doesn't do anything else, and also the reset driver doesn't
work without calling this function. Thus, it does not make much sense
that this function is independent from pm_reset_init().
Delete the separate call to starfive_jh7110_inst_init(), and instead
just call this function inside pm_reset_init().
Doing this also fixes another problem: if starfive_jh7110_inst_init()
returns an error code, it gets propagated to final_init() and OpenSBI
hangs. This hang is not necessary, because failures within
starfive_jh7110_inst_init() only mean OpenSBI cannot perform reboot or
shutdown, but the system can still function normally.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Tested-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Jh7110's reset driver needs power management device and clock controller
device to work. Currently, the driver proceed anyway without these
devices, and invalid addresses (jh7110_inst.pmu_reg_base and
jh7110_inst.clk_reg_base) are used during reboot, which causes
unpredictable broken behaviors.
If these devices are not present, return -SBI_ENODEV.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Tested-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
OpenSBI uses the device tree compatible string "stf,axp15060-regulator"
for the regulator node. However, the string used by U-Boot (and Linux)
is actually "x-powers,axp15060". As OpenSBI gets the device tree from
U-Boot, this causes the regulator device to be undetected, and OpenSBI
does not use this device to perform board reset/shutdown.
Rename this device tree compatible string to match U-Boot (and Linux).
Signed-off-by: Nam Cao <namcao@linutronix.de>
Acked-by: Minda Chen <minda.chen@starfivetech.com>
Tested-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
pmic_ops() is only called if a compatible device is found in device
tree. It is redundant for this function to check the compability again.
Remove this check.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Tested-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The current code gets the I2C offset address using the device tree node
name: it get the I2C device index from the 4th character in the node
name (for example, "i2c5" -> i2c device 5). However, the device tree
node's name in U-Boot is actually just "i2c" without the number, so the
current code cannot be used with the device tree from U-Boot.
Get the I2C offset address from the "clocks" property instead.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Reviewed-by: Minda Chen <minda.chen@starfivetech.com>
Tested-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Starfive names the system clock device tree node "starfive,jh7110-clkgen"
in all their git repositories. However, a different name is used in
upstream U-Boot (and also Linux): "starfive,jh7110-syscrg". Since
OpenSBI gets the device tree from U-Boot, this inconsistency leads the
problem that OpenSBI doesn't know the system clock device exists.
Correct this name to keep the consistency.
Signed-off-by: Nam Cao <namcao@linutronix.de>
Acked-by: Minda Chen <minda.chen@starfivetech.com>
Tested-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
add reboot and poweroff support. The whole reboot and shutdown
pm op includes shutdown jh7110 pmu device power domain
and access on board pmic register through I2C.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
