Initial platform support for ESWIN Computing EIC7700 based on public SoC
datasheet[1] and tested on HiFive Premier P550. Vendor U-boot/Linux boots
fine, and I've tested Geekbench 6.5.0 Preview and got scores on par with
the vendor OpenSBI. System shutdown/reboot for HiFive Premier P550 and
other boards will be implemented in subsequent commits. At this point,
only SoC-level warm reset is implemented.
The files and functions are intentionally named as eic770x in many places
for future enhancements to support the 2 die version of the same SoC,
namely EIC7702, seen on DC-ROMA AI PC FML13V03 [2]. This patch set only
deals with the single die version, and the assumption is we can be either
die with id=0 or id=1, but there's only a single die in the system, or we
are only using a single die out of 2. However, the way the SoC handles 2-
die greatly affects how we configure it in a 1-die setup. EIC770X address
map has die 0/1 memory regions interleaved (see comments in eic770x.c).
If only 1 die is connected or active, it creates holes in the address map
for those regions corresponding to the remote die. When speculative-
execution or HW prefetcher touches data-cacheable regions that happen to
fall into those holes, it can trigger bus error. Specifically:
- Remote (non-existent) die L3 zero device
- Remote (non-existent) die cached memory region
- Other holes in Memory Port
To make matters worse, EIC770X doesn't have cache coherent DMA, and due
to the fact that the P550 core lacks Svpbmt, the SoC maps main memory
twice as different regions, so it can bypass cache and fetch the data
directly from memory. In address space, we have two memory regions, one
as cached, the other as uncached. Thus, we also need an extra PMP entry
to protect OpenSBI blob from the uncached window. To do this, platform
code requires single_fw_region, otherwise, we'll run out of PMP entries.
EIC770X also have several feature disable/enable CSRs accessible in M
mode. By default many core features such as speculation and HW prefetch
are disabled, and M mode software is responsible of enabling. Hence,
introduce 4 new build time tunable parameters to Kconfig, which reflects
the values get updated to those CSRs:
- ESWIN_EIC770X_FEAT0_CFG
- ESWIN_EIC770X_FEAT1_CFG
- ESWIN_EIC770X_L1_HWPF_CFG
- ESWIN_EIC770X_L2_HWPF_CFG
The default values are somewhat optimal for generic workloads. They are
dumped when running SiFive's vendor OpenSBI, and in addition, with my
own tuning to address the perf regression reported by drmpeg [3]
To build the firmware+u-boot blob, Use the following, and docs [4] for
testing it with UART boot without flashing:
make FW_TEXT_START=0x80000000 \
FW_PAYLOAD_OFFSET=0x200000 \
FW_PAYLOAD_PATH=u-boot-nodtb.bin \
FW_PAYLOAD_FDT_ADDR=0xf8000000 \
FW_FDT_PATH=u-boot.dtb
[1] https://github.com/eswincomputing/EIC7700X-SoC-Technical-Reference-Manual
[2] https://github.com/geerlingguy/sbc-reviews/issues/82
[3] https://forums.sifive.com/t/low-1-core-stream-bandwidth/7274/15
[4] https://github.com/ganboing/EIC770x-Docs/blob/main/p550/bootchain/UART-Boot.md
Signed-off-by: Bo Gan <ganboing@gmail.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Link: https://lore.kernel.org/r/20251218104243.562667-6-ganboing@gmail.com
Signed-off-by: Anup Patel <anup@brainfault.org>
The SiFive SMC0 controls the clock and power domain of the core complex
on the SiFive platform. The core complex enters the low power state
after the secondary cores enter the tile power gating and last core
execute the `CEASE` instruction with the corresponding SMC0
configurations. The devices that inside both tile power domain and core
complex power domain will be off, including caches and timer. Therefore
we need to flush the last level cache before entering the core complex
power gating and update the timer after waking up.
Reviewed-by: Cyan Yang <cyan.yang@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Nick Hu <nick.hu@sifive.com>
Link: https://lore.kernel.org/r/20251020-cache-upstream-v7-12-69a132447d8a@sifive.com
Signed-off-by: Anup Patel <anup@brainfault.org>
The supervisor software can directly receive most of the system MSIs
except P2A doorbell and MSIs preferred to be handled in M-mode.
Add MPXY RPMI mailbox client driver for the System MSI service group.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Instead of having one common FDT MPXY RPMI mailbox client drivers
for various RPMI service groups, split this driver into two parts:
1) Common MPXY RPMI mailbox client library
2) MPXY driver for RPMI clock service group
The above split enables having a separate MPXY driver for each
RPMI clock service group and #1 (above) will allow code sharing
between various MPXY RPMI drivers.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Add a generic RPMI mailbox client driver which provides a MPXY channel.
Initially, this driver only supports RPMI clock service group but can
be extended to support multiple RPMI service groups.
Signed-off-by: Rahul Pathak <rpathak@ventanamicro.com>
Co-developed-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
The generic platform can have multiple MPXY drivers so add a simple
FDT based MPXY driver framework.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
The generic platform can have multiple CPPC drivers so add a simple
FDT based CPPC driver framework.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
The RPMI HSM service group provides set of routine to query and control
power states of a Hart. Add RPMI based Hart State Management (HSM) driver.
Signed-off-by: Subrahmanya Lingappa <slingappa@ventanamicro.com>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Add RPMI based system suspend driver.
To test this, execute the follwoing in Linux:
$ echo mem > /sys/power/state
To wake up, execute the following command on qemu monitor terminal:
(qemu) system_wakeup
Signed-off-by: Subrahmanya Lingappa <slingappa@ventanamicro.com>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
The generic platform can have multiple system suspend drivers so add a
simple FDT based system suspend driver framework.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Add RPMI based driver for system reset and enable it in the generic
platform defconfig
Signed-off-by: Rahul Pathak <rpathak@ventanamicro.com>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
The RISC-V Platform Management Interface (RPMI) defines a messaging protocol
and shared memory based transport for bi-directional communication with an
on-chip or external microcontroller.
To support RPMI in OpenSBI, add:
1) The RPMI messaging protocol defines and helper macros
2) A FDT mailbox driver for the RPMI shared memory transport
Signed-off-by: Rahul Pathak <rpathak@ventanamicro.com>
Co-developed-by: Subrahmanya Lingappa <slingappa@ventanamicro.com>
Signed-off-by: Subrahmanya Lingappa <slingappa@ventanamicro.com>
Co-developed-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
SG2042 uses an onboard MCU to provide reset function.
Add reset driver to support this onboard MCU.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
In the past, we used fdt_reset_thead to help customers with prototype
verification. However, with the emergence of the Big-little SoC system,
it can no longer meet the demand. Therefore, we use zero_stage_boot
instead of fdt_reset_thead. It cleans up the opensbi code and ends the
disputation of reset_sample's dts.
This patch removes the fdt_reset_thead component and updates the related
doc.
Signed-off-by: Guo Ren <guoren@linux.alibaba.com>
Signed-off-by: Guo Ren <guoren@kernel.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
The TLB entries remain functional all the time once added in T-HEAD th1520
and Sophgo sg2042 (even if the MMU is then disabled afterwards). If there
are some stale TLB entries that contains the address of SBI, it will cause
unexpected memory access and issue a illegal instruction error. To avoid
this, a TLB flush is needed to drop these TLB entries before any memory
access in the trap handler.
To handle this workaroud, add a custom trap handler with executing TLB flush
first in the T-HEAD platform to fix affected socs.
Signed-off-by: Inochi Amaoto <inochiama@outlook.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
The functionality of SiFive Test reset driver is easily available
through Syscon reset driver so let us remove the SiFive Test driver.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Let us have common FDT based reset driver for syscon reboot and
poweroff. The device tree bindings for syscon reboot and poweroff
are already available in the Linux kernel sources.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Let us add a simple FDT based system regmap driver which follows the
device tree bindings already defined in the Linux kernel.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Xiang W <wxjstz@126.com>
We add a simple FDT based regmap framework which is built on top of
generic regmap library. The phandle of FDT regmap DT node is treated
as unique regmap ID. The FDT based regmap drivers will be probed
on-demand from fdt_regmap_get_by_phandle() and fdt_regmap_get()
called by the regmap client drivers.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Xiang W <wxjstz@126.com>
We add generic regmap access library which is independent of
hardware description format (FDT or ACPI). The OpenSBI platform
support or regmap drivers can register regmap instances which
can be discovered by different regmap clients based on the
unique ID of regmap instances.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Xiang W <wxjstz@126.com>
Add a driver for the Synopsys DesignWare APB GPIO IP block found in many
SoCs.
Signed-off-by: Ben Dooks <ben.dooks@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
add reboot and poweroff support. The whole reboot and shutdown
pm op includes shutdown jh7110 pmu device power domain
and access on board pmic register through I2C.
Signed-off-by: Minda Chen <minda.chen@starfivetech.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
We move andes directory to platform/generic as the necessary fdt
drivers are available, the users can enable the console, timer, ipi,
irqchip and reset devices by adding device tree nodes stated in the
docs/platform/andes-ae350.md.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Anup Patel <anup@brainfault.org>
We update generic platform to use kconfig for enabling/disabling
platform overrides. We also enable all platform overrides in generic
platform defconfig.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Tested-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Atish Patra <atishp@rivosinc.com>
Tested-by: Atish Patra <atishp@rivosinc.com>
We update gpio drivers makefile to use kconfig for enabling/disabling
drivers. To avoid compile errors, we also enable appropriate gpio
drivers for each platform.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Tested-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Atish Patra <atishp@rivosinc.com>
Tested-by: Atish Patra <atishp@rivosinc.com>
We update i2c drivers makefile to use kconfig for enabling/disabling
drivers. To avoid compile errors, we also enable appropriate i2c
drivers for each platform.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Tested-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Atish Patra <atishp@rivosinc.com>
Tested-by: Atish Patra <atishp@rivosinc.com>
We update irqchip drivers makefile to use kconfig for enabling/disabling
drivers. To avoid compile errors, we also enable appropriate irqchip
drivers for each platform.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Tested-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Atish Patra <atishp@rivosinc.com>
Tested-by: Atish Patra <atishp@rivosinc.com>
We update ipi drivers makefile to use kconfig for enabling/disabling
drivers. To avoid compile errors, we also enable appropriate ipi
drivers for each platform.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Tested-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Atish Patra <atishp@rivosinc.com>
Tested-by: Atish Patra <atishp@rivosinc.com>
We update timer drivers makefile to use kconfig for enabling/disabling
drivers. To avoid compile errors, we also enable appropriate timer
drivers for each platform.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Tested-by: Andrew Jones <ajones@ventanamicro.com>
Acked-by: Atish Patra <atishp@rivosinc.com>
Tested-by: Atish Patra <atishp@rivosinc.com>
